Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hello,
I'm trying to lower the power consumption in the s.c. "System ON" mode. I need to run in System ON mode to keep the RTC running. However I need to wake the CPU on...
hi ,
I use SR3 V1.2 to test. I enable ANR, play the recording directly in the loop.
About every five seconds, a second or so of unusual sound appears. The rest of the...
Hi,
I can't understand what is DFU example inside /examples/dfu folder and what is /bin/bootloader/? I read DFU quick start guide, but where is source code of bootloader...
I try debug my app in keil debugger but it's often raised app: SOFTDEVICE: ASSERTION FAILED in SEGGER after step down through the code (in few steps).
My app based on buttonless_dfu...
Hi,
I have a doubt regarding buffer setting in SPIS.
In the SDK15 SPIS example, buffers are set using nrfx_spis_buffers_set(...) and it works perfectly.
I was wondering...
Hi All,
I am using nrf mesh SDK v2.2.0 and nrf SDK v15.0.0.
I have created a new model in nrf mesh SDK, this model is publishing scanned data on group address.
When...
Hi,
I was working on the HID mouse example and noticed that the example gets disconnected from my mobile phone once i start moving the cursor.
I also noticed that the...
Hello,
I am performing current measurements on custom hardware with the nRF52840 and comparing my results with the values in the nRF52840 product specification. I noticed...
I have downloaded nrf5_SDK_for_Mesh_v2.1.1_src and tryign to build the client and server example to test the Lighting Mesh example from the Android/iOS apps available on the...
Dear Nordic Team
I have changed pwm driver example as you see in bellow . i also observed the codes which you linked for pwm. Bellow code works without the effect of update_pwm...
We are trying the HID Keyboard example using SDK 12 with no modifications on the nRF52 (PCA10040) board. We are able to pair and connect on both iOS and Android the first...
Hi,
I have a nrf52 DK. I currently tested apps on run smartphone. Similar to nrfconnect, toolbox, uart.
Laptops also have bluetooth. Can i use laptop's bluetooth to communicate...
Hi, I would like to create a new target,but nRF52810 only can be compiled with makefile and I don't know makefile too much.
I try to edit the makefile with my own target...
Hi guys,
I'm using following setup NRF51822, SD130, SDK 12.3.0. I control one transistor with PWM output via timer 1. Before enabling PWM I start 8bit ADC task to measure...
Does the Nordic UART Service (NUS) have a facility to confirm when a sent message has been received by the peer?
In particular, to confirm when an NUS message sent by a...
