Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
KConfig is warning me: CONFIG_LSM6DSO was assigned the value y, but got the value n. Missing dependencies: DT_HAS_ST_LSM6DSO_ENABLED
I am running on a custom board, the...
Hello,
I am testing nRF7002DK board using nRF Connect SDK.
Does nRF7002 support Wi-Fi roaming such as 802.11k, 802.11r, 802.11v?
If it supports Wi-Fi roaming, please...
Hello,
I have a question regarding the sys_poweroff() function. In my device, there is a mode where the board (including the nRF52840 chip and GPIOs) remains powered, but...
Hi,
I am developing an application with the nRF5340 microcontroller.
I need to use the I2C module, but if I insert the CONFIG_I2C=y configuration in my prj.conf file,...
When disconnecting and connecting BLE, if the J-Link debugger is connected, BLE_EVT_DISCONNECTED in ble_evt_handler is executed, but if the debugger is not connected and the...
Hi Support Team,
Our product is based on nrf5340 and ncs V2.5.2. I developed a Windows application(based on .NET8.0 and Windows SDK11) to provision and configure the system...
Hi,
I have a custom nPM1100 borad and want to charge the battery. My schemetic shows here, I notice the battery cannot be charged. My shcemetic shows below:
I have confirmed...
Hi Support team,
I encountered some flash overflow errors when I enabled the MCUboot on nrf5340. Could I ask several questions?
My situations and requirements: 1. My project...
Dear Nordic Semiconductor Team,
We are very interested in your nRF7002DK development kit and are exploring its potential for use in an open-source IP camera project. Our...
Hi, I am using an two nrf5340 with hci_ipc enabled one acting as central and one as peripheral built on v2.9.0
The issue I am having is that the supervision timeout doesn...
We have a project with a device acting as a ble peripheral and a broadcast sink. First the ACL connection is set up and then it will scan for and sync to a broadcast with...
Hi,
With the attached code, the timer0_event_handler() is only called once - is there something else I need to do in the ISR or at initialisation-time to ensure that it...
Hi all! :)
I struggle to initialize GNSS when I don't have a connection with LTE. Examples that could be found on dev academy initializates GNNS after LTE has been initialized...
Hello,
I’m wondering if there is a way to separate CELL and Wi-Fi location data from GNSS location data in the Location library. Currently, we use nRF Cloud for location...
Hello.
I am trying to boot the nRF54L15DK from an external power source.
Referencing this page , I supplied 3.3V to P6, but the SoC could not boot.
The 'VDDM_nRF' through...
