Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
I'm currently using NCS 2.9.0.
However, the default certificate path is C:\ncs\v2.9.0\modules\lib\matter\credentials\development\attestation .
I used the parameters below...
Hi,
I have question about a project I'm running on nRF connect sdk 2.9.1.
I noticed that whenever an i2c sensor device device_init() is returning a value not equal...
I can't connect my newly purchased PPK2 to Power Profiler V4.2.1. The log shows: 2025-04-22T22:23:19.069Z DEBUG Sending event "ppk: running nrfutil device" 2025-04-22T22:23...
Hi Nordic Team,
I'm currently working on a BLE project using the nRF52840 DK with the nRF5 SDK (not using SoftDevice Controller), and I’ve run into a critical issue related...
I want to build the sample usb_hci.
After i create a build config there are warning and the process fails
warning: <choice BT_HCI_BUS_TYPE> (defined at boards/arm/ubx_evknorab10_nrf5340...
I am trying to scan for sensors on an I2C bus using the nrf54L15 and Zephyr RTOS. I modified the i2c example from here: https://github.com/iFransL/i2c-scanner/tree/main
...
Hi,
I'm working on an application where the system should enter System OFF mode after some button activity and wake up (restart) on a button press or USB connection.
When...
Hello,
I’m trying to understand exactly how the location module works in the Assert Tracker V2 application. I want to see the NMEA data in the logs, but I’m not sure how...
im trying to develop a prototype that uses a thingy53 and lvgl to draw a screen on a solomon ssd1306 attached via i2c (kwiic) but am having issues with getting it to build...
NCS 2.9.1 - NRF5340DK
I am trying to use multiple compare channels on Timer1 (output_timer) such that an interrupt handler fires for both compare values, the second of which...
I am working with SDK v2.3.0 and a custom board with nRF9160
When I wanted to start my project again after some time, the build configuration had disappeared.
And creating...
I used a mesh example (the example name is "mesh") for testing, and enabled low-power nodes using CONFIG_BT_MESH_LOW_POWER =y, and disabled the automatic start of low-power...
I used ncs2.9.1. I download the mesh dfu distributor and mesh dfu target examples to two devices respectively, and successfully updated the mesh node through shell commands...
When my mtd device is connected to a thread network, what should I do if I want to untie and join another thread network? How should I untie and clear the network information...
