here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello,
I just downloaded nRF connect for Desktop App, and plugged in PCA 10100 2. 0. 0 , 2023, 3.
I ran quick start, and this is what I get.
Any explanation on why...
I'm developing firmware for a RAK4630 for IOT purposes. According to the datasheet, the average consumption of the nrf52840 is 1.5 ua in system ON mode. Mine is measuring...
I am trying to control ws2812 LED (1 LED) with NRF52840 using nrf connect SDK, I was able to control it with no problem when I set building optimization to debug optimization...
So as the title... the Creating a custom driver using the sensor API exercise for the current SDK versions is missing from the nRF Connect SDK Intermediate course. Are there...
We urgently need to add support for Band 40 (B40) to our product. Our use case is very specific, and as far as we understand, the NRF91 currently does not support B40. We...
I had a project that I made with SDK v2.6.0 and Toolchain v2.6.0 with an Actinius Icarus board.
Today I wanted to continue with my project so I build it and everything was...
Hello DevZone.
Is it possible to enable Notify and Indicate method at the same time in NCS?
From my side, this doesn't work on my project, neither on Nordic sample ...
Hello Nordic Team,
I previously asked about how to configure the internal load capacitance for the 32 MHz crystal on nRF54L, and I’ve successfully applied the solution provided...
Dear Engineer
When the advertiser and the scanner enter the connect callback, a timestamp will be printed immediately. The problem now is that the advertiser and the scanner...
Hi Nordic engineer
I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start.
Due to limitation of power resource...
Hello,I tryed to install the CMSIS Wirzard in SES on the video from https://www.youtube.com/watch?v=b0MxWaAjMco But it deosn't work. I don't know why. I did read the DevZone...
Hi,
I recently started working with the nRF54L15DK and nRF Connect SDK 2.9.1. I'm trying to use I2C21 and SPI00, but I noticed that certain pins on the development kit always...
Hey guys,
I just came up with an error I can't explain with my current zephyr knowledge and I really can't workaround because the other MCU isn't programmable and needs...
I am currentry trying to evaluate the RAYTAC-MDBT50Q-CX-40.
Raytac Corporation 勁達國際電子股份有限公司
But sample applications(helloworld, blinky) don't work.
I installed the...
Hi,
I was working on Channel Sounding for my NRF54L15 boards and suddenly the boards in "connected devices" were no longer visible. I don't know how it happened and what...
