Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
We have a system with multiple log backends enabled. The goal is to ultimately keep one of the backends to globally only see errors/warnings while the other gets all the a...
I know the nordic chips do not support Bluetooth classic, however I would like to setup a nordic device as an HCI device that pretends to have to Bluetooth classic support...
Hi,
In trying to take the PPI example code from nRF5_SDK_17.1.0_ddde560 and adapt it to use RTC for an event-end-point, I get the following error:
Error[Pe020]: identifier...
*EDIT* - Using NCS 2.9 I am using the QSPI peripheral to communicate with a display.
1. I initialize the QSPI peripheral. I have tried both blocking and non-blocking. Both...
Hello everyone,
I am using the NRF5340-DK development board, but I am having trouble restarting advertising when my smartphone connects or disconnects from the board. Once...
I have created a barebones blinky example as a way to start developing for the dual cores on the nRF53, but I can't seem to synchronize them. The code on both cores is nearly...
Hi,
This is a followup on https://devzone.nordicsemi.com/f/nordic-q-a/119259/synchronisation-between-tx-and-rx-in-connectionless-direction-finding
We now have a synchronised...
I am using OpenThread network and working on CoAP Client and Server examples (Customized). Everything working fine when devices are on main power.
My client devices are...
I am running VSCode with the latest nRF extension. I am on v2.9.1 of the SDK
I created a new app and copied the bluetooth_st_ble_sensor sample project.
I would like to...
Hi,
I used the nRF52840 board with SDK v2.8.0 .
When we tried to build this example code, we encountered the following error: v2.8.0/zephyr/include/zephyr/device.h:92...
Hi!
S132, SDK17.1, nRF52832
Very strange behavior, I connected my central to the bonded peripherial success and got an BLE_GAP_EVT_CONNECTED event, but when I disconnected...
Hello,
I'm working on a custom board with a nrf54l15 chip.
I would like to add an interruption on the GPIO P2.10. But I get an error -ENOTSUP with gpio_pin_interrupt_configure_dt...
Hi Support Team,
I tried several ways to set the image version but failed. My SDK is ncs V2.5.2. 1. set(CONFIG_MCUBOOT_IMAGE_VERSION "1.0.0") in CMakeLists.txt: did not...
Recently I've had an issue with 3 of our nRF9160 based products during production (several hundred of the same hardware/firmware/SIMs work fine). The issue is that while the...
Hello Nordic support,
My application is a Zigbee coordinator application on nrf52840 based on nRF5 SDK for Thread and Zigbee v4.2.0. I was able to pair a Zigbee end device...
