Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
i compiled the ble_uart_app project it got downloaded in to the NRF51DK but the bluetooth is not getting turned on ,usually the output of this example is LED has to be turned...
Thanks for your support folks!
I am trying to read some bytes I have wrote in a MX25R8035F. From the datasheet, if you send 0x03 (READ) + 3 Byte address, then the memory...
Hi,
We want to receive the data in laptop over the BLE like nRF UART mobile APP.
we sending and receiving data in Mobile app but we can't get the app for desktop.
we...
Hi,
1-I did some test for nrf51422 (SDK12.3 + soft device S130) power consumption. result as below:
-system on sleep mode( without UART and BLE Advertise ):90uA
-system...
I am working on developing BLE app using connection oriented channel . I am using nordic semiconductor as a peripheral device and iPhone 6 as central manager.
I am able...
Hi,
I am working on a project that requires extremely low power consumption (20-50 uA) at max. We are currently consuming around 5.5mA. The project uses SPI to communicate...
Dear Nordic Team,
Thanks for supporting.
Currently i am try to check mesh network. I want mesh example code using keil IDE. I am using SDK12.3.0 and Hardware is nRF52...
How can i calculate the average current consumption, so i can estimate battery life.
This application uses Gazell to send data.
Peripherals used:
-UART for logging ...
Hi
I would like to connect the nRF52810 to 2 devices via UART interface by switching the Rx and TX GPIO pins by the software in realtime.
Is it possible? what is the method...
Hii
I m using Fanstel Ev board (BT840F) using nRF5248 Fimware.
i want to set maximum transmission power +8dbm in FANSTEL Ev Board but i got an error code 7 is Indicate...
Hi,guys.
In my experiment, Firstly,I creat an app_timer work every 20ms interval
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE, false); err_code = app_timer_create...
Hi everyone,
Recently, I used the nrf52832 learning board to learn SDK13.0.0, when I see SAADC, tell the truth, this exampe is a bit difficult for me to understand.
My...
Hi
I am trying (for the first time) to deal with flash. Hence, I started by a simple app, without BLE/SD (blinker)
The problem is that, the first API call pstorage_init...
1. Connected to nRFgo Motherboard's nRF ISP and NRF24LE1E SPI pin
[nRF ISP]
[NRF24LE1E의 SPI]
2. In nRFgo Studio, Features> 2.4 GHz is disabled
3. I want to know...
