Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I try to make a simple project based on a "simple message model" ( https://devzone.nordicsemi.com/f/nordic-q-a/29836/send-and-receive-a-string-via-access-layer ) with Mesh...
Hi，
SDK：nRF5_SDK_15.0.0_a53641a
Chip：nRF52810
Example BLE：ble_app_uart（pca10040e \ s112）
Example 2.4G：esb_prx（pca10040）
I am working on BLE and 2.4G integration...
Hi，
I use SDK is ：nRF5_SDK_15.0.0_a53641a
But the SDK version in the link seems to be lower
devzone.nordicsemi.com/.../setting-up-the-timeslot-api
I am going to step...
I'm developing an application to communicate with a smartphone. I have the need of writing characteristics with the size bigger than the negotiated MTU, so I'm exploring Queued...
Hi guys, our team now are trying to used nrf52832 to stream audio to ios app, and as you know we are in trouble.
Here are some info about our test env:
1. mobile app...
Hi everyone,
I wanted to add a second UART (UARTE1) to the CLI example in the OpenThread SDK 0.10.0 since UART0 is used by CLI but I was not able to find any documentation...
Hi,
Can't get rid of compilation error about undefined NRFX_SPI0_INST_IDX after adding nrfx_spi driver. Searched the forums and found similar issues but none of the suggested...
Sir,
Did you succesfully compile the NRF5 mesh on SEGGER STUDIO ? I did try with updated segger but i am getting the same error!
And i cant see too the sdk_config.h to...
Hi,
I just received nRF52-DK recently.
I am using Ubuntu 16.04 (64-bits) OS.
I installed JLink_Linux_V620b_x86_64.deb and was using nRF5x-Command-Line-Tools_9_6_0_Linux...
Hi, I am developing an SPIS interface on the nRF51822 using SDK v12.3.
I have configured my device for EasyDMA and I expected to see a continuous stream of data being transmitted...
Hi.
I applied https://github.com/crfosse/Thingy-52-to-nRF52xx project to get thing'y motion sensor by nRF52840 DK.
When I init DK, it discovered only 7 UUID so euler,...
Hi Everyone
I am trying to use BME which is an i2c/twi sensor and EPaper which is an SPI based module. In my code i am using TWI INSTANCE ID 0 AND SPI INSTANCE ID 0.
I...
Hi all:
I am developing the driver of ST LIS3DH and its mcu is NRF52.
If I want to read the value of whoami.
I am not sure if I need call the function of
nrf_drv_twi_tx...
Hi everyone. I'm starting from scratch and using as reference the example/ble_peripheral/ble_app_template.
I'm using Embedded Studio 3.50 + Jlink V6.32 / The chip is nRF52832...
