I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi guys,
On my application, I ported the code from TWI_scanner example (SDK14) and it is connected to a temperature sensor the which is read every 45 seconds, It is working...
As far as I can tell, Shockburst isn't officially supported on the nRF52840 in SDK 15. However, I have seen some success from others with this configuration, but after making...
Hi,
I have been working with the NRF52832, and trying to capture raw ADC data with the help of TWI bus. I have imported the necessary libraries (i'll attach the code below...
I have used aes_all_cli example to test computation time for AEAD EAX/GCM/CCM. I have shortened the plain text to 16 bytes, added pin toggling on encryption function enter...
I don’t have a lot of information as I’ve been totally unsuccessful in debugging this.
In short, we have a SPI peripheral that was working under SDK 14.2. Under 15.0 we...
Hi,
I am trying the connect MIO Fuse heart rate band. It follows the standard specified by Bluetooth SIG i.e Heart rate profile UUID is 180D and the heart rate measurement...
I'm currently woking on doing my own DFU system, the system should work this way : the central gets a new version of the app via the internet network and it should update...
How to establish communication with a peripheral through I2C ?what are the functions needed to define address and write and read from the slave address
Hi,
I followed the instructions for importing the Thing:52 firmware into SES and managed to get the firmware compiled and loading, and the code reaches the main function...
Hi,
I'm following DFU quick start guide and I'm using mesh SDK v2.0.1, I have a problem in step 4 wheere I need to generate a hex version of device page, I did this :
...
Hello,
Are there any conditions where the sd_ble_gap_disconnect() will not immediately terminate the link?
My Setup: Nrf52, SDK 13.0.0, own board, based from HRM code...
Hi!
I want to start scan in central mode after one connect has established and I received success evt PM_EVT_CONN_SEC_SUCCEEDED:
In a SDK13 I can make same, but at SDK15...
Hello!
On the firmware for a certain product, we are using the scheduler module to manage the access to the peripherals (SPI, TWI, Timer, ...), and have also enabled its...
I implemented manufacturer specific advertising to transmit important data without having to connect to the ble peripheral. These data can change over time so I need to be...
I measured the power consumption on NRF52840 DK with project peripheral blinky (SDK15.0.0). The average current is 704uA and the base current is 680uA when connecting to another...
