Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi, I am using nRF5340 for my unicast Audio server example where the nRF5340DK is the headset and my mobile device is the audio source. I have taken the unicast audio server...
Hi,
I just can not download nRF_DeviceFamilyPack 8.44.1 from this link developer.nordicsemi.com/.../ It comes up an error of the server. Does any body knows how to get this...
I'm following the tutorial Exercise 1 – Custom board for single-core SoC using ncs v2.9.0 with one slight difference in that I'm using a nRF52DK with nRF52832 because that...
I built a custom board with the nrf5340 and a SD card connected to non-standard gpios. My SD card is connected via SPI over the P0.14, P0.15, P0.16, P0.17, respectively for...
The latest toolchain has removed "serverArgs": from debug configuration in nrfConnect 2025.4.106
Is is mandatory as we only have RTT on our FF board and no serial...
Hello everyone,
I am trying to test the SLM on the nRF9160DK on NCS 2.9.0. (SDK and toolchain) I want to control the nRF9160 with an external MCU, so for this the application...
Hello,
Our product that we currently design is based on the nRF52840 QFAA and w e are looking to achieve FCC, CE and RED compliance.
I would like to request any certificates...
Hi,
I'm working with the nRF54L15 SoC and running into an issue when using UARTE21 together with SMP over Bluetooth . Here's what I’ve observed:
UARTE21 works perfectly...
Hi,
I have an issue with nRF Kconfig GUI in VS Code.
My prj.conf is empty, and the _defconfig file of my board contains this:
When I open the GUI and...
I'm trying to get the USB Mass Storage sample working on the nRF52840 using SDK 2.9. I followed the official guide here: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hi!
I have somehow softbricked my nrf54L15 dk. This happened by using nrf conncet board configurator. First symptom was no uart logs and now I get this crash via RTT logging...
This issue is a follow-up to the previous one： 341132
When upgrading our device from Matter 1.1 to Matter 1.3 firmware via OTA, the MCUBoot program in the old firmware fails...
Hello,
I am conducting a feasibility study on implementing Auracast capabilities using the nRF5340 Audio DK with nRF Connect SDK v2.9.0. My goal is to investigate the potential...
Hi,
Recently, when I tried to obtain Bluetooth certification with nRF52840.
I found that there is a new requirement as shown below
RF:P1 - TRM/CA/03 Power Control
...
