GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
HI
[environment] · NRF 51822 · SDK 12.3
We are developing application software including DTM.
In the application software, a flag to start DTM using FDS is written in...
Hello all,
I've recently started developing an nRF5 device (using Segger on Ubuntu, and SDK15.2.0), and for what I have read regarding peripheral drivers, I should be...
Hello all!
I'm trying to optimize power consumption for project based on nRF51802 and external host MCU. My current platform and toolchain:
1. nRF51802 as Bluetooth controller...
Hello, i am using NRF52840 board with NRF52840 SDK version 15.2 with softdevice 140 Version 6.1. I am using the BLE_NUS_UART_C example and id like to send a scan request to...
Dear nordic,
BLE advertising happens in 3 channel(37,38,39) and scanner scans these channel based on scan interval consecutively
I want to scan single channel instead...
Using nRF Connect for both iOS and Android, the advertised name is the same for both apps, i.e, DeviceX.
Clicking on the device information also shows the Complete Local...
Hello,
I am using an nRF52840PDK (master) to use an SPI peripheral, where my code is based on examples\peripheral\spi. My IDE is Segger Embedded Studio and I am using SDK...
Hi Nordic Team!
Please find below attached the schematic for my custom nRF52832 proto board. The boards are already manufactured and are in the bringing-up stage. The designs...
Hi, I've encountered a problem described here: https://devzone.nordicsemi.com/f/nordic-q-a/37917/nfc-issue-when-migrating-to-sdk11 Since I could not figure out the issue,...
SDK 15.0, PCA 10056 (1.0.0)
Is it possible to let the relay-example from the SDK 15.0 run in a way, so that the long-range feature of Bt 5 is supported between the Peripheral...
Hello,
I'm using a nRF51422 uController (Custom board) with the Softdevice s130 withe SDK 11. I want to go back into the bootloader from my application after I told the...
Hello Everyone ,
By using sdk version 15 for NRF52840 I wish to connect the lsm9ds1 sensor to it and using seggar embedded studios IDE. The header files available in google...
Hello, what is the best way to provide optional enable or disable option for a user in terms of keeping BLE module powered on or off. I am thinking of 2 options , can you...
Hi everyone,
I'm currently working on a nrf52832 board and i got an issue on Gpio config after a reset.
I configure a gpio with a register value of 4, low level, output...
