I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Sending array unit8 type data using BLE failed, and attempting to take 2 bytes of data from the array and send it also failed. Does anyone know what this log error means?...
Hello,
Since a few days ago, when I start VS Code, I get the following warning:
But when I check the settings in VS Code, v1.x.x is not there.
What could be the...
I have a Raytac MDBT50Q-CX and cannot seem to flash it correctly. The flash succeeds, but the device is no longer recognized by Windows or (raspberry pi) Linux.
My goal...
I am currently working with the nrf54l15, I have both the DK and a custom board I designed. I am running into issues with the uart00 peripheral when using custom GPIO pins...
Hi,
I am using nRF52840 DK and I am following Nordic Academy nRF Connect SDK Fundamentals. I installed SDK 2.9.1 and toolchain 2.9.1
I copied the sample blinky and encountering...
Hi everyone,
I'm using the nRF54L15-DK and trying to implement a simple low-power cycle where the board:
Measures sensor values
Sends them via CoAP over OpenThread...
I am migrating from a child_image type project to the newer sysbuild system used in ncs v2.9.0.
My application is based on the ncs nrf5340_audio application, but my application...
Hi，
When I use NCS V2.5.0 （board：nRF 52840），I want to set the Non-Connectable and Scannable Extended Advertising.My code as follows.I use the APP nRF Connect for moblie...
Hi everyone,
Environment setup: - I am using Zephyr OS 2.5.0 running on nRF52840 board. - MIRA mesh integrated in the application.
Problem description: - Firmware A has...
When both ethernet and WiFi are supported on one MCU (with both sharing the same L2 implementation, only one network device being active at a time), does it matter if both...
Hi, I previously wrote about an unexpected behaviour which I've made a diagram for below. It's relatively simple though, the COMP watches a voltage and fires a toggle event...
For the GetAssistanceData endpoint (POST /location/agnss), if we are using the x-custom-device-id header instead of a device token and registered devices, how can we view...
Dear All,
We have a custom design with a nRF9160 powered by Lithium primary batteries.
When batteries end of life is coming or sometimes when harsh environmental operating...
Hi,
USB CDC EPOUT stops working as the USB incoming traffic data rate increases. The symptoms of this issue align with the Errata 199. The workaround for Errata 199 is...
I'm currently working on a custom board based on the nRF52840 , using SoftDevice S140 v7.0.1 and nRF5 SDK v16.0.1 . I’ve integrated the BLE Buttonless DFU example ( examples...
