FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
Hi, On the nrf54L15 with MCU boot enabled, what is approximately the fastest time that the chip could boot and set a gpio line high, if everything not critical is disabled...
Hi,
We are using a modified version of the multi-service sample for nRF9151. Generally, FOTA updates from the nRF Cloud work well.
Once we deploy the FOTA update in the...
Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
i am working on i2c device on zephyr NCS v3.0 i want to read the i2c address . which sample example to follow and what are the changes to be made in the sample example.
I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi,
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
Background : To set up a Matter ICD (Internet Connectivity Device) and Thread as a SSD (Sleepy End Device). Here are the detailed settings:
Currently, the Matter over...
Dear Nordic Team,
I was trying to use the I2C peripheral on the nRF5340 with clock speed of 1MHz, but I kept getting the error "unsupported speed". I was using the function...
Hello! This is the third time I'm asking something about the same project, but I'm running into problems one after the other.
The current problem is this - the hogp object...
I am using NCS v2.9.1 and trying to enable a bootloader chain with NSIB and MCUboot. The regular setup works fine, however if I try to enable the minimal configuration, I...
I am using nrf5340 audio DK,
The project I use is v3.0.2 .\samples\nrf5340\empty_app_core\. If the board target is nrf5340 audio DK
a compilation error will occur. build...
Hello DevZone,
It seems that the nRF 52840 DK has 1MB of internal flash memory and it can be extended by external memory via QPSI. I have found External Memory source where...
Hi all,
I have attached one external antenna to my initiator device and one to my reflector, both devices being nrf 54l15 dk and the antenna are connected to the SWF connector...
I have followed the guide Adding clusters to Matter application to add two TemperatureMeasurement clusters to the Template sample.
I have flashed this onto an nRF52840-DK...