I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hardware:
a. nRF52840 DK baord as client
b. nRF52840 DK baord as server
c. nRF52840 DK baord as provisioner.
procedure:
1. Through segger embedded studio I have...
I am using nRF52832 with SDK 14. My app has bootloader and dfu. Everything was working fine with external crystal. I changed my clock source to RC and used these recommended...
hello, I have developed nrf52840 for multiprotocol ble/zigbee.
I want to simply send & receive zigbee packet not using zboss network.
I already tested example "wireless_uart...
I have two nrf52832 boards, both being developed with SDK v11 and the s132 soft device.
Board one is given commands over UART to communicate over ESB with board two. Board...
Summary of Issue: 8 dongles are used in a test system that each dongle will communicate with 1 device. Testing can start ok but after some runs, one of the dongles can not...
According to nRF52840 Product Specification v1.0, a ll the reference circuits are designed for use with a 50 Ω single-ended antenna. Why is the calculated result by AppCAD...
What would be the best example to start with my project which involves sending sensor data to mobile phone applications using ble? i have nrf52 DK and SDK 15.0
Thanks,
We're using RTT with an 52832 and it works fairly well, really can't complain much except...
On my PC everytime I launch a debug session I need to launch RTT viewer exe...
I'm using Rigado BMD350 evaluation board. I'm printing to serial port (COM3, speed 112500) using NRF_LOG_INFO.
However, the logging does not appear until debugging is...
In a recent project, me and my team have been trying to send data from 3 PTX devices to a single PRX device (the devices are all nRF24L01+) at a constant rate of 1600Hz from...
hi all!
Like two of my predecessors, I am trying to put a CR95HF into operation. I chose the nRF52832 DK as MCU (SDK 15).
[thread= https://devzone.nordicsemi.com/f/nordic...
I changed only source clock part to internal clock and it doesn't do advertising. When I debug it, it starts to run. When I finish the debug session advertising stops again...
Hi,
I've built a custom board with nRF52832, without other MCU like PCA10040. I use a FT232RL to bridge the USB to nrf UART, flashed nrf5 uart connection firmware ble_connectivity_s132_uart_pca10040...
Hi, I using nrf52810 with custom BLE profile and 4 sec advertising + continuous RTC. Device is battery powered (750 mAh) and PMDC motor equipped. Most of time (90% of day...
Hi,
I am designing my custom board with the nrf52832, which would perform the BLE and I2C functions. I wonder what necessary and basic peripherals it needs, like crystal...
