to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
On a NRF52DK Board, There is an on-board programmer done with ATSAM3U2C seen as a Segger programmer or a Jlink Progammer.
By mistake, I erased the entire flash of this...
I was trying to update J-link firmware (using link [https://devzone.nordicsemi.com/question/170895/nrf52832-jlink-stop-working-after-entering-bootloader-mode/] ) into interface...
Hi,
The following vulnerability described as Bluetooth implementations may not sufficiently validate elliptic curve parameters during Diffie-Hellman key exchange in the...
I want to use the serial DFU. Do you have any examples? I tried with ble_app_buttonless_dfu, not UART DFU.If you have a detailed reference, please let me know.thank you very...
Hi,
I am using the MCU on a board with sensors that are sampled in a very high rate (~100Hz).
I am having issues when trying to send the data with notification on more...
Hi,
I am using sdk12.2 and customised nrf52 board.
I want to interface ultrasonic sensor with nrf52. In this I am enabling trigger pin as high and after sometime my...
Dear All,
I am working with SDK version 15 and softdevice 132.
I want the device to advertise for 1 minute. Then go to low power mode. Again wake up after 5 minutes...
I have twe NRF24L01 module,one set Tx mode with autoask,and another set Rx mode without autoask,
The channel and address are same.
Can I use this mode to communication...
I have problem flashing main program and SoftDevice on the nrf 51822 module. I have Keil version 5.24 and I am using SDK v12.3 .
I can flash SoftDevice easily but after...
Hi,
I init the UART pin with the AIN pin such as P0.05, but the program will run into __WEAK void app_error_fault_handler(uint32_t id, uint32_t pc, uint32_t info) every...
Hi Everyone
I have been trying to do some simple led blinking by generating events , however i need to do that if a button_0 is pressed for some duration.
Here is a code...
We are using SDK 15.0 and Softdevice 6.0, FreeRTOS 8.2.1
Is there a way to use softdevice and NRF_SDH_DISPATCH_MODEL_INTERRUPT?
If not, it means SDH task MUST be the highest...
Dear Sir,
I am using SDK15 and sodtdevice S132. I am testing on the kit BMD300.
I am using nRFConnect App in andoird to connect to the device and check the services...
Dear all,
I used SDK 12.3 buttonless functoin with PCA10028(nRF51422), and I occur some problem.
I did some testing as below:
case 1. softdevice+bootloader
case 2...
hi Nordic ,
I am developing an USB product with the nRF52840.
Can you can request the use of Nordic’s vendor ID in conjunction with an assigned unique Product ID?
Or...
