Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello, I am using SDK 15 & Softdevice 6, I am using NRF52840.
I have merged the USB CDC into a multi-link example. I confirmed that it worked, and the project was successful...
Hi
Is the DCDC enabled or disabled by default when using the DTM example in SDK v15.0.0? We can't find any reference to it so we assume it is disabled, but just wanted...
Hi guys,
On my application, I ported the code from TWI_scanner example (SDK14) and it is connected to a temperature sensor the which is read every 45 seconds, It is working...
As far as I can tell, Shockburst isn't officially supported on the nRF52840 in SDK 15. However, I have seen some success from others with this configuration, but after making...
Hi,
I have been working with the NRF52832, and trying to capture raw ADC data with the help of TWI bus. I have imported the necessary libraries (i'll attach the code below...
I have used aes_all_cli example to test computation time for AEAD EAX/GCM/CCM. I have shortened the plain text to 16 bytes, added pin toggling on encryption function enter...
I don’t have a lot of information as I’ve been totally unsuccessful in debugging this.
In short, we have a SPI peripheral that was working under SDK 14.2. Under 15.0 we...
Hi,
I am trying the connect MIO Fuse heart rate band. It follows the standard specified by Bluetooth SIG i.e Heart rate profile UUID is 180D and the heart rate measurement...
I'm currently woking on doing my own DFU system, the system should work this way : the central gets a new version of the app via the internet network and it should update...
How to establish communication with a peripheral through I2C ?what are the functions needed to define address and write and read from the slave address
Hi,
I followed the instructions for importing the Thing:52 firmware into SES and managed to get the firmware compiled and loading, and the code reaches the main function...
Hi,
I'm following DFU quick start guide and I'm using mesh SDK v2.0.1, I have a problem in step 4 wheere I need to generate a hex version of device page, I did this :
...
Hello,
Are there any conditions where the sd_ble_gap_disconnect() will not immediately terminate the link?
My Setup: Nrf52, SDK 13.0.0, own board, based from HRM code...
Hi!
I want to start scan in central mode after one connect has established and I received success evt PM_EVT_CONN_SEC_SUCCEEDED:
In a SDK13 I can make same, but at SDK15...
