But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi
I am using SDK 14.2 secure bootloader with IAR and SES build. My IAR project is working with DFU upgradation but my SES Hex file is not working
Procedure Followed...
Hi, I use s132 and SDK15 to work with nrf52832. In code I set up RTC and CC to trigger every N ticks. It works as expected and time periods counted correctly. However, when...
Hi,
I can't find the whisper mode（-30dbm TX power） on nRF52832, which is available on nRF51822.
Does is have been disabled on on nRF52832?
Regards,
Aaron
I like to build a node act as client as well as server. Is it possible to build as control model in mesh and shall i get any example for control model. Please give me any...
Hello Nordic experts,
I just received an nRF52840 USB Dongle and I am trying to run one of the examples with softdevice. I am working on nRF5_SDK_15.0.0_a53641a. So, I first...
Hi,
my application runs on a bare-metal nrf52 using softdevice. I need to compress data saved in flash of size ~160KB before sending over BLE and I need to do the compression...
Greetings everyone,
i am trying to migrate from SDK 14.2 to SDK 15 but I got this problem with updating "advertising" and "scan response data". I have read other threads...
Hi, I know NRF52840 support mulitprotocol BLE/Zigbee/Thread. Would NRF52832 support those as well? For cost reason, my smart home application product would really prefer NRF52832...
Hi,
I got one of nRF52 DKs. Is there any chance that we can use this DK similar to nRF51 DK as a sniffer in near future?
I tried to program the board with the HEX file...
Hi all,
I'm interested in the new nRF52840 USB dongle. Currently I'm working on adding some security functionalities to nRF52840 PDK.
Is nRF52840 USB dongle compatible...
Hello,
I am doing a project on a NRF52DK, using SDK15 and SES.
I have been trying to implement a basic feature, which will be a part of a bigger system:
Detect interrupt...
In the course of investigating higher than expected current consumption, I've been looking at nRF52832 errata, and one that I'm concerned about is #78, use of Timer STOP task...
Hello,
I have been trying to merge the pwm_library (or gpiote) with ble_uarte examples to have controle on the pwm signal through UART events
I think i merged correctly...
Hi everyone.
I'm trying to transfer new firmware over UART for just only one node in mesh network.
My node will connect to other wireless MCU(ESP32, ESP8266....) over...
