Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi
I was wondering if it's possible to scan for both 1MBPS and CODED at the same time, or should I initiate 2 different scans.
using this configuration initiates error...
Hello,
we developed our electronics with your chip nRF52840, but we have problem with communication throught BLE. We tried our firmware on dev kit with this chip. It was...
Hello,
I am looking for wireless communication solution between two devices with a maximum distance of 5-10m for controlling a speed of the electric-assisted vehicle (basically...
Hi,
I use SDK 12.3.0 with PCA10040 board, and try running experimental_ble_app_buttonless_dfu. It works fine when I use Keil to compile, but doesn't when use GNU. I open...
Hi,
I've tried connecting to the nRF52840 Dongle using nRF connect as explained in : ://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.tools%2Fdita%2Ftools...
Hi, I've been trying to build a custom characteristic and so far I can display a single digit number on my BLE app. My update value function looks like this:
And my add...
I am using SEGGER Embedded Studio to program the nRF51822 module. When I was going through the manual for setting up the environment for SEGGER Embedded studio, I found that...
I want to use a buzzer on my board.
The environment in use is below. · SDK15 · Nrf 52 · Nrf 52832_xxaa · S132_nrf52_6.0.0_softdevice.hex
My start is "nRF5_SDK_15.0.0_a53641a...
Hi support team,
I'm using a PDK(PCA10056) with nrf52840 and SDK 15.0. Recently I was developing a BLE bootloader for DFU OTA.
Since the ble bootloader was depended on...
Hi
I have been trying to get example ble_app_hrs to run after compilation on my 52832 dev board (pca10040).
The specific example is: C:\Keil_v5\ARM\PACK\NordicSemiconductor...
Hello,
after migrating from SDK14.2.0 to SDK15.0.0 I was suddenly unable to connect my central and peripheral devices. After looking into it with a Bluetooth sniffer, I...
Hey, I want to create a Mesh Monitor, to do this I want to create the follow setup:
Mesh consist of Several servers with Heartbeat message Tx/Rx enabled send periodically...
Hello,
I'm experiencing some problems reconnecting an iOS device (possibly same thing on Android) to my peripheral in the background. This happens most of the times after...
I'm using S140 6.0.0 and associated MBR on an nRF52840 with a custom boot loader derived from the nRF5 SDK 15.0.0 examples.
I'd like to perform some custom actions as soon...
Kindly give suitable example or suggestion for Eddystone Relay / Rebroadcaster. I have checked on Beaconing example but it could not rebroadcase eddystone beacon.
