Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi Team Nordic,
According to the AM2302 (DHT22) datasheet, the data pin will be pulled to high state in idle state. But in my case, when i am reading the data pin before...
I'm developing nFR52832 to communicate with the PC via UART. commands are sent to the nRF and for each command nRF responds with some data back to the PC via UART.
The UART...
I'm trying to include the SPI driver in my project.
I have added the .c file into my project:
I have included the path into the project:
I have enabled the SPI...
I try to make bootloader via USART for my application. I'm using: nRF51422rev.2, SDK6.1.0, S210 ver3.0.0. KEIL5.11. I did everything like describes in post here:
devzone...
I want to implement BLE security in one of my project where central and peripheral connection should be secured rather than only characteristic protection.
And any way to...
I'm developing a custom driver (C++) for the SPI master. Somewhere I've made a mistake, where the first received byte is written with a memory offset in SPI mode 1. I.e. we...
Hi,
I have a BLE application, which I want to interface with PC via serial communication through USB.
It seems that just adding Softdevice breaks the USB_CDC_ACM example...
Hi all,
As a followup of this question, I started with the Thingy Mesh Provisioning Demo v0.5. However, I cannot get this version working possibly due to some unclear points...
Hi,
Am developing a beacon using nrf52810. I have a doubt on how to program the nrf52810 which I made using the schematics and layouts given in the Nordic website for nrf52810...
I am noticing that FDS requires me to specify a "record size", but there is no maximum specified, so I am testing it. Currently my program attempts to store 32 words, but...
I want to add some code to static void app_onoff_server_set_cb(const app_onoff_server_t * p_server, bool onoff) in light switch server application.
My intention is when...
When nrf51422 passed the authentication, when entering the rx mode of DTM, there was always a -59dbm launch at the 2.79GHz frequency point, what caused it, and how to eliminate...
Hi, I am trying to interface MPU6050 IMU module with NRF52832 DK.
I need to send the Accelerometer and gyroscope data to mobile app by using BLE_UART program
this is my...
Hi,
I'm trying to send a broadcast message from my client to all my server. Actually i'm working over a modifed version of the light switch example.
i saw that in the...
