Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi
I'm using sd_app_evt_wait(); to go into low_power mode. For some reason it coming back , but I can't figure out why.
Peace of code I am executing is;
while (nrf_fstorage_is_busy...
I am trying to print out a string debugging information. But got below error.
No problem change to printf or cast char array name to uint32_t. See first 2 sentence.
char...
I have python 2 and 3 on my Macbook. I can't run nrfutil which I believe is due to the python installation. I need to keep python 3 for other utilities. I would like to run...
Hello!
We're building radio modules with the nRF52840, one with the a frontend amplifier and one without. Both are exhibiting excessive 2nd and 3rd harmonic emissions. ...
Currently, we are testing that 「buttonless DFU + Bonding valid」 in our App.
But After performing F / W Update with DFU, other BLE Service became invisible.(※2)
So, as...
Hi,
I am currently in an attempt of revising an old board, it uses an ANT+ module which is soon going to be out of production. With the nRF52840, if I were to use the ANT...
Dear Sir,
I had a project is lighting the LED matrix, we choose the LED IC is TLC5958 and MCU is using nRF52832.
Now, we have a question is how to change the GPIO output...
Hello all,
I used SDK15 and nRF52840 DK made a long range advertising and long range connected.
I modified the ble_app_uart_c and ble_app_uart example, the long range...
Hi
i am using the sdk 14.0
i am working with sph0645 i2s microphone , i have tested the microphone and it is working fine with the nrf 52 on 912600 baud rate. Now i wan...
Next week, we have a meeting with our customer to give them an overview on all our BLE solutions (they are interested in module) but I also want to give them an overview on...
nrf52832, SDK 15.0.0
I develop the project based on the example 'ble_app_buttonless_dfu'
But when I want to add some peripherals, such as SAADC, SPI and PPI, and some...
I'm seeing strange corruption in the nrf52840 virtual COM/UART (the one that goes through USB and the JLink interface MCU).
The nrf52840 is running the UART serialization...
I had setup nRF sniffer with below software and hardware, but the Wireshark seen unable capture BLE data.
nRF Sniffer software nrf_sniffer_2.0.0-beta-1_51296aa.zip ...
