I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello all,
I plan on using the blinking LED authentication in mesh configuration, I have seen the nrf mesh app video where it is done using the app but I want to achieve...
Hello.
I am using the NRF52832 Evaluation board.
If I click the connected board of Device Manager to upload program application, nrfgo studio will be turned off without...
Hello,
I have an existing customer who has products based upon the nRF24L01+.
He would like to upgrade to the newer nRF52x series but is concerned about backwards compatibility...
Dear Nordic
I found a example using nrfx_twim_rx() to scan slaves, I was just wondering if I can use nrfx_twim_tx() to scan slave devices by send zero byte data? I use nrfx_twim_tx...
Hi,
In the BR Bluetooth (not BLE) there is a profile called OPP (object push profile) that enbled sending text messages to mobile phone with out the need to install any...
Please check the file attached in the attachment section. I am trying to compare NRF52 series chip. Please correct me if I am wrong and please add the missing values of NRF52810...
I see in the SDK that PB-remote is experimental.
"Provisioning over Mesh (PB-remote) (experimental)"
We are working on a very large project and are in the process of choosing...
I try to load my nRF52 with app via ble from windows 10 laptop.
nRF52 dev kit is loaded with the Softdevice and Bootloader from nRF5_SDK_12.1.0\examples\dfu\ble_dfu_send_hex...
I have an external 32MHZ crystal on my custom board.I want to configure it to 32 MHZ external crystal to operate the chip. i changed the some register configuration in software...
all works fine with iphone that mean data stored, bond 's information that has been persisted during DFU processing.everything works with iphone. but when the device that...
Dear Nordic Team,
Thanks for supporting.
Now i want support for single channel(Ch 37) advertise , please support anyone. I am using ble_app_uart example.
My SDK : SDK12...
I'm running some stress tests on a nRF52832-based product, with the following setup:
- SDK 12.0.0
- SD 3.1.0
- Compatibility modes 1 and 2 enabled.
The device exposes...
hi ,
1. How do I migrate the codec OPUS part of SR3 ? I want to use it for audio. But migration always fails. Any migration examples?
2. How effective is ANR work? Are...
