I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
I'm working with NSIB (nRF Secure Immutable Bootloader) and trying to manually sign an application image that is built separately — without using SB_CONFIG_SECURE_BOOT_APPCORE...
I have a custom board that uses nrf52832 and I would like to add FOTA support using Bluetooth.
When I build the code using the nrf Connect inside VS code, it creates a DFU...
Hello guys good Morning,
I am currently studying the examples in the Nordic Dev Academy. I am in lesson 5 from the "NRF Connect SDK Fundamentals", and I managed to toggle...
Hi,
I'm attempting to restore my Thingy91x to communicate with my instance of nRF Cloud (I had removed the certificates previously to test out the connection to another...
Hi,
I am using a custom nRF52832 board with multiple ADC channel readings sequentially. I am trying to read thermistor (NTC) value on channel 7 and not getting accurate...
Hi community,
I'm using the following setup:
nRF5340DK
nRF Connect SDK v2.6.0
B0 , upgradable secure MCUBoot, and application
Statically defined partitions in...
Hi,
My requirements are:
My essential need is a one-to-one connection between central and peripheral .
But when my central receives the specified command to start scanning...
Hello there, this is my first post here.
I'm facing a wall in my project development.
Here is the issue, so during start up of the NRF52832 I see a high current draw for...
Hello, I need your help about BLE channels. Currently, I use only the primary channel 38 for advertising data but, when the data are sent, I don't have the information of...
Hello,
I am currently working on connecting a Thingy:91x to a Cube Orange autopilot (Pixhawk 2.1) in order to receive telemetry data over UART using the MAVLink protocol...
We need a parter to develop the Thread terminal base on Nordice nRF52840, the project will be design in China and produce in Germany. Is there any reliable company could provide...
I noticed that through apply_old_config.h configuration values like NRFX_CLOCK_ENABLED in sdk_config.h simply get overriden by the old CLOCK_ENABLED, so that there is no point...
The scanner can be informed of the synchronization information as soon as it receives an ADV_EXT_IND PDU, and then it can later scan only AUX_SYNC_IND PDUs. at this point...
I am using NRF52832 Custom Board and Have to implement deep sleep for 1 minute and have to limit the current consumption to a very minimal value during the sleep cycle I have...
I am trying to get the J-Link RTT viewer working with the Sysbuild Peripheral LBS Sample from the BLE FOTA DevAcademy lesson . I need the SEGGER J-Link RTT viewer working...
