I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hi
I am running UBUNTU 32bit
Which "nRF Connect for Desktop" version does run on 32bit LINUX?
I have tried several with no success.
Thanks for any help ti get...
hello.
I want test dfu example.
so I was compile & download secure_bootloader example(nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader).
I just compiled and...
Hello everyone,
I want to know about Connection parameters updated means and why to use it as mentioned above and when did the next connection parameter is updated and...
In a current project we have a nRF52 Bluetooth application where the Central communicates directly with a Peripheral (also nRF52). The nRF5 SKD V14.0.0 or newer is used for...
Hello,
I have been following this case to create my own bootloader for nRF52810, but I'm using gcc/Segger Embedded Studio instead of Keil.
I have modified bootloader_secure_ble...
Hi.all:
I'm doing a project, it include freeRTOS+emwin(TFT screen SPI-->32Mhz)+BLE(central+peripheral)+FATFS+flash(qspi)+TF card(spi)+GPS(uart)+wifi(uart)+other IC(spi)...
I am working with a SmartThings Multipurpose Sensor connected to a nRF52840-DK running the ZigBee CLI as a coordinator. I am able to have the sensor join the network and I...
SDK11, NRF51822
if I use the fstorage_test at the applicaiton_init(void), then runs ok.
but on my product, I use a key to power the system, if I use the fstorage_test...
We are implementing DFU over serial to the nRF52832 from another microcontroller.
We are using SDKv15.30 and a slightly modified the serial bootloader from the DFU bootloader...
Hello, I am developing a big project with the nrf52832 + several peripheral devices and I want to integrate the notion of unit test to my project (in Segger embedded studio...
When trying to build my BLE Mesh app based on light_switch server example app from nrf5 SDK for Mesh with added functionalities (like detecting GPIO state changes and firing...
I'm attempting to create a DFU update using the the ble_app_uart example coupled with the BLE DFU bootloader. It's not unlike this case .
SDK = v16.0.0
nrfutil = v6.0...
Hello Nordic Team,
I have loaded the ble_app_uart example on my custom hardware. There is a button connected to P0.13. When that button is pressed I receive a NRF_BREAKPOINT_COND...
Our nRF52840 is connected via UARTE @ UART_1 to a modem which does not have a WAKE pin - the only method of waking it from sleep is to send a UART break. Is there any way...
