I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
To the kind attention of Nordic support team,
Could you please give a very quick look at those attached gerber files? Do you think there is something that is better to correct...
Hi Nordic team support,
I want to test communication range between nRF528xx device that support LE coded with samsung galaxy s10 (support LE coded also)
1. If I configure...
For some reason I can't quite program the nRF9160 on the development board using Segger Embedded Studio (SES) when I create a new project. I must be doing something wrong...
When I set "report_incomplete_evts = 1", I get a NRF_ERROR_NOT_SUPPORTED (0x06) error.
If I comment it out, everything work as expected. I want to use it for exended advertise...
Hi All,
I need to find the RF Tx power setting of the nRF52840 by reading from the register. I understand this is possible through Jlink and the following command:
--memrd...
Hello,
I am developping a project on with the nRF9160 and I would like to have the LTE and GPS working concurently. I managed to have both working separatelly on my custom...
Hi. I am confused about flash endurance. In the product specification for the nRF52832, there is a note that flash endurance is 10000 write/erase cycles:
Does it mean...
Hi,
What's the easiest way to subscribe to the MQTT messages that the thingy91 sends to the nRF cloud?
I have tried setting it up with a node-red and a python client...
I am newbie in nrf51822 and I am going to do project nrf51822 with BLE mesh. I have some questions regarding to this, please support me: Does Nrf51822 support BLE Mesh? Does...
To the kind attention of Nordic support team,
In PCA10059 hardware files C10, C13 and C25 are not conected when I see in the bill of material. But it seems that in the real...
Hi,
I am currently just trying to clone the nRF connect sdk according to the getting started assistent.
All the first steps just worked fine, but I ran into a problem...
Dears?
When I click the download link of nRF Sniffer v2.x ,it show "page not found(Error404)"
Would you help me?
nRF Sniffer User Guide v2.2 is to be used with the...
Hi Sir,
In normal, we can see three virtual COM ports in nRF connect - programmer, first is for nRF9160, second is for nRF52840, the last is for nRF9160 but not use.
Then...
Hi
I have a wired situation in my project. Everything is working fine when I am running my heart-rate device with the debugger. When I detach the debugger or just power...
Hello
A project that recently made a sensor found that the timer consumes a lot of power.
I built a timer to collect sensor data in the timer handler.
Sensor only...
