I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Dear All,
I have noticed the following behaviour:
When the modem goes to PSM, it is not possible to retrieve the RSRP, using the CESQ or the XMONITOR AT commands. This...
Hi,
I am using NRF52840 DK in our project . I am using 15.3.0 SDK and soft device s140 in our project .Here the nrf52840 dk board is client and other controller bluetooth...
Hello,
SDK: 15.3.0
Hardware: nRF52840-DK
I am attempting to make a simple dimmer with 2 pins/LEDs. I have used the following post.
https://devzone.nordicsemi.com/f...
After following all the steps on the nRF Connect v3.2.0 Getting Started Assistant.
I get the following error after pressing OK.
Any idea what is wrong?
Am I missing...
Hello,
I am trying to integrate the calendar example (using RTC 2), with a current time service(CTS) client and and custom service server on a nRF52940 DK.
I want to use...
Hi,
Firstly, I am able to read a 16-bit service with a 16-bit characteristic and able to use that to get a handle for reading and writing to the peripheral.
But i am unable...
Hello,
after the nRF9160 RRC connection the base stations inactivity timer determinates when the connection switches to RRC idle. Is there a AT command to read to the networks...
I am testing a BLE connection between a nRF52840 and a Thingy:52 using the nRF connect for Desktops.
It asks "Device must be programmed, do you want to proceed?" every time...
Trying to get started with the Thingy:91
- It's connecting to NRF Cloud and reporting data.
Problems:
1. Keeps blinking blue and does not get a GPS lock. I did leave...
Hi everybody,
We are going to develop on nrf52833 our new product. I have some questions regarding this new module:
1- Is the module available to buy online?
2- I saw...
Hello,
We are working on a Tag and Trace type asset monitoring application, that requires scanning several thousand (>6000) beacons in a closed room of about 15feetx15feet...
I am programming and using the monitor mode with Keil seeming ly OK with nrf52-DK dev board however when I program my custom PCB it gives me an error and says the bit cannot...
I designed a reduced size PCB that used an nRF52832 and will act as a BLE HID device.
With the original nRF52DK evaluation board I was able to use the example ble_app_hids_mouse...
