I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Dear NRF community and support This is a followup question to the DevZone post https://devzone.nordicsemi.com/f/nordic-q-a/2860/flashing-bootloader-and-application-via-j-link...
From everything I know and understand of the system architecture, this shouldn't be possible, but one of our early production units out in the fields has twice now apparently...
I'm designing a two-part computer input device: Part A will communicate with the computer over BLE, but it must also be able to forward along messages from Part B. Here's...
Hi,
I am trying to update the MTU between the central and peripheral to the maximum MTU.
at the connection interrupt from the central side I added
but I got error...
For nRF52832 I see in the datasheet:
I OFF_RAMOFF_GPIO System OFF, No RAM retention, Wake on GPIO,
While for nRF52840 only “System OFF, no RAM retention, wake on reset...
I have an iOS App which is just designed for updating our device firmware OTA. It uses the Nordic DFU library, updated to the latest cocoapod. It connects to our device, and...
Hi,
I use OpenWRT and nRF52832 to develop a BLE gateway, the nRF52832 connected to OenWRT through UART. Now,we need the uart serial DFU of nRF52832, and I found that nrfutil...
I am looking for some advice before diving in to what could be a big waste of time. In my existing Thread implementation, I use nRF52840's in two different configurations...
Hi all!
I am using mesh sdk v4.10 and sdk 16.0 with an nrf52840 custom hardware. I have a question regarding the mesh event handler. I am seeing something weird which I...
I am trying to run DHT sensor on the nrf9160 using the sample provided by zephyr (can be found under zephyr>samples>sensor>dht). The code was meant to run on nrf52. Is there...
hello everyone,
I'm using SDK15.2 in nrf52832. I need to update my sensors value(Temperature, Humidity and accelerometer) data to advertising non connectable beacon. How...
Hi,
I'm using nRF52832 board and I'm modifying the Eddystone BLE Application in ble_peripheral example in SDK 16.0.0. I'm trying to get the characteristic value of ADV Advertising...
Hello, we are creating a nordic peripheral using an nrf52832 and SoftdDevice S112 and SDK 16.0. We need to store quite a bit of data non-volatilely, at a fairly fast rate...
hi
im use nrf52840 as a gazell device which run the demo \nRF5_SDK_16.0.0_98a08e2\examples\proprietary_rf\gzll\gzp_desktop_emulator\pca10056 ,and use nrf24lu1p
(\nrfready_desktop_2_v3...
