I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
Hi,
If the following function is used, how to solve this error:
#include <nrfx_reset_reason.h>
void check_and_clear_reset_reason ( void )
{
// 获取复位原因
uint32_t...
2025-06-13T08:43:42.649Z INFO Initialising the bundled nrfutil device 2025-06-13T08:43:42.652Z DEBUG Started watching devices 2025-06-13T08:43:44.400Z INFO Using the bundled...
We are in the process of finalizing the RF transceiver chip for custom protocol development.
Please suggest the suitable chip and any reference implementations available...
We want to design a setup for simultanious translation of up to 3 translators and up to 30 people receiving a translation.
Is it posible to setup a single transmitter, sending...
Hi everyone,
I am trying to monitor and measure the signal strenth variation by varying the positon of the developement kit NRF51 and i tried with the proximity example...
Hi,
I'm using v1.21 nRFgo. As programming 51series ,
(1)I want to know if the program check the hex file before the log dialog shows "programmed successful"?
(2)And...
I run nRF51 with S110 and advertising at least standard battery service. I can see my device in LightBlue scan window but in iOS Settings->Bluetooth it is not picked up. Which...
i am aiming to design a simple data transfer network. i am using 2 DKs. the first one is the central which runs a modified version of MULtilink Central Example and the seond...
I have continued to build upon the Nordic sdk10:gzll_ack_payload example using gcc-4.9-2015q1 on Linux. The differences are:
added UART for debugging (running at 460800...
Hello Nordevzone, so far, to the best of my knowledge, you can send data using API call sd_ble_gatts_hvx() with "notification packet" (quotemarks due to my limited knowledge...
AS i am trying to utilize GCC for more than 32 KB code size,
i use Eclipse which provides more friendly interface.
However, i am still experiencing some setting issues....
Hi,
Details:
I am using nrf sdk 10.0.0 and s130 Softdevice.I am using nrfgo studio for flashing SD,Application Hex files.I am using this nrfgo studio for past three months...
Hi,
I'm developing nRF51 proximity based device using nRF51822 that acts as BLE peripheral. It advertises continuously using connectable indirect mode.
User has Android...
app: nrf tool uart on iphone 5s
sdk: v8.1.0
softdevice: s110
example: ble_app_uart.
i have modify it based on the answer :
link text
my advertsing init as...
The device I completed has similar RSSI values at approximately zero distance as my development kit; starting with default Tx of 0dBm from the nRF51822 I achieve approximately...
I am having an issue implementing a WS2812b driver for the nrf51422 using the 210 softdevice. We currently have ANT enabled with a tx master only channel setup. The WS2812b...
What I would like to do is run a basic SPI program that reads data from a register on a non Nordic transceiver chip. My nRF51 would have to act as the master because the transceiver...
