Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
I'm in the process of upgrading one of our applications from NCS 2.6.1 to 3.0.1. According to this document, the only versions of NCS that support modem firmware 2.0.1 and...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
Hi,
I got a question on power consumption:
In my case, I do not need RF functions on most of time. If disable RF function, what working current of nRF51822 would be? ...
when phone connect to the device, I print the connected address.
However, I find that the bluetooth address is not same with the phone bluetooth address.
here is the debug...
Hi,
I am trying to include temperature (read from DS18B20) in advertisement data using BLE_UUID_HEALTH_THERMOMETER_SERVICE. So far it works fine, but my temperature is...
Hey,
I am using twi_hw_master.c and twi_master.h libraries for twi and want to disable i2c to save power when not in use.
I use the following two lines to disable the i2c...
Hi,
i am using Eclipse 'Mars' and Segger V5.10c to debug some of the SDK examples. The Eclipse command line shows only binary garbage. How can I get the garbage readable...
Hi,I am using s130 softdevice and SDK9.0 .I add static passkey(123456)in my project base on ble_app_uart project and basic functions have been achieved.But I have a question...
Hello!
Is it fine to ready NRF_RADIO->FREQUENCY right after receipt of BLE_GAP_EVT_ADV_REPORT?
Does its value have a relationship with recent adv. report?
hello there when i am trying to open project C:\nRF51_SDK_8.1.0_b6ed55f\examples\ble_peripheral\ble_app_template - Copy\pca10028\s110\arm4. i am getting error like
Third...
Hi,
I have set connection interval as 1.8s.
But i have transmit data every 1 min.
I noticed that BLE transmits data every 1.8sec.
Can someone please tell me what is...
I have just exported a project from mbed, to the Keil uVision4 tool chain.
Create New Project "BLE_Thermometer" on mbed.
"BLE example for the Health-Thermometer...
I see in the information about the nRF51 talking about the support of 4.2. But it is not clear to me the extend of it. I am focus on the link layer and I would like to know...
Is it possible to implement 2 peripheral in one device (need to connect a peripheral device with two different centrals)? When should i expect for this feature?
I have a question about how much memory is required for app timers.
The comments for APP_TIMER_BUF_SIZE state that the buffer size must be one more than actually needed...
