I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Source: nRF6939-CD-NVS-5.4-livecd.zip Resource download path failure: www.nordicsemi.com/.../Download-infotabs Please provide me with a valid resource download path
Hi,
Recently, I am trying to make a nRF52810 project to run the sample code based on nRF52832.
The application code size is used in nRF52832, Code=56840 RO-data=9600 RW...
I am trying to use SPI master + UART concurrently on the nRF52840 dongle. I am aware that the GPIO pins on the dongle can be used for SPI or UART. However, when trying to...
My nrf9160 which has the v1.0.0 modem and using v1.0.0 sdk has suddenly started continuouly resetting when i try to run asset tracker application. I have tried at-command...
Hello,
I am trying to build the lte_ble_gateway sample. I keep getting a JavaScript Alert TEST_RANDOM_GENERATOR.
I got something simalure with the bluetooth hci uart...
nRF52811 has only one receiver. Most accurate direction finding can be made based on estimation of phase difference between two signals received in two spaced antennas. Such...
Hello – My project needs to report its indoor position to the cloud (no GPS). I intend on using known positions of iBeacons SSID/RSSI coupled with trilateration math – fully...
Hi team, I developed own project based on /examples/dfu/secure_bootloader/pca10056e_ble/ses/. In the original project there was only Release config (no Debug). I modified...
I am trying to figure out how to configure my peripheral such that when a central client tires to enable the service changed characteristic that it succeeds. I am desperately...
I'm working on an application where I will need to initialize the modem, send/receive messages and then turn it down to low power until the next checkin. I did a real simple...
I have read that at each connection event master will send the first packet (empty payload).
In a case where slave latency > 1, the slave will not be listening to master...
Hi devs,
It is not a real issue it is about a possible misconception about app_timer
For my application, I am using multiples timers using app_timer_create. From my understanding...
So I'm coming to the nRF52832 from a couple decades worth of light occasional programming, mostly data analysis and scientific computing in nature, and primarily in C/C++...
Hello,
In my setup, I have 5 clients (buttons) that all report to the same server (lightbulb).
I'm using the Mesh SDK 3.2 light switch example with static provisioning...
Hi everyone, I successfully followed all the steps of the Getting Started Assistant on Windows 10 x64, but I am unable to open the Asset Tracker project because of some errors...
