i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm totally new to Nordic solutions. I was programming a lot in assembler in 8051 era 20 years ago. Now I feel lost in that new solutions.
I have PCA10040. It is connected...
Hi everybody
I'm working on an application where I want to sample microphone data with the adc (NRF52 DK board, nRF52832) and send it over BLE to a central device. I've...
Hello, we just made a raw board with the MDBT40, which use a nrf51422 chip. I downloaded SDK version v12.3.0 (which supports nrf51) on the nordic website. With nrfGoStudio...
Hello, I am trying to use the 'nrf51-pwm-library ' on mBed with a nrf51822 on RedBearLab Nano.
I copied the nrf_pwm.h/c files and they compile, but I never get any sort...
Hello everybody ! Designing with the development board nRF52832 and SDK14.2.
My code is based on the code of the "ble_app_multilink_central" on which, I added some of the...
Hi
in pcb designing of the nrf52832 we use two oscillators one is 32 MHz and another one is 32 kHz.
can't we use both 32 kHz instead of one 32 MHz for saving power consumption...
I write the code base the nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_uart
I add some button and led function in it.
and add weight measure mode with HX711,...
Hello World...
I wanna share with my new progress to implement machine learning for nRF51822. Here it is how to make it possible. after questioning to forum that using machine...
hi,
I want to know why app_timer and nrf_drv_timer conflict。App_timer is used to broadcast data。When App_timer time out ,timer1 start.
Cannot broadcast data after initializing...
Hello everyone,
I generate an interruption when an rising edge is detected on one of my I/O.
It seems that the interruption doesn't trigger correctly for an input frequency...
Hi,
(SDK 14.2, S140 V5.0-2.alpha)
I'm working on a ble project that includes to verify mac addresses.
For the Bluetooth SIG specs, when a device has a public adress...
I just update my sdk to 15.0.0, which use the softdevice s132_nrf_6.0.0. but when I try to generate the application package, I found the nrfutil do not give the sd-req code...
Hi,
Where the Firmware is being stored in the flash??
In which address of the flash the firmware is being stored when i flash the code??
In what file type ,the firmware...
Hi.
I am trying to set up a simple Ble beacon on a PCA10040 and a sniffer on another PCA10040.
IDE = Segger Embedded Studio for ARM (This works fine)
The beacon uses...
