Developing an implementation for UltraWideBandImpl for a different UWB hardware solution (not the provided qm35 implementation) and running into integration problems
The...
HI, Good day to you. we kindly request your confirmation of the COF ( Country OF fabrication) origin for the NRF52810-QFAA-R component. We would be most grateful. the label...
Hi, We're in the product validation stage of development with nRF54L15, part of the validation is temperature cycling, we noticed that devices seem to be "stuck" in sleep...
Hi,
I am trying to configure an Xiao Seeed Studio nrf54l15 sense to transmit pre-processed sensor data via BLE extended advertisements. As the payload is more than 251 bytes...
In this post mentioned: "Maximum theoretical peak data rate is 3.4 Mbps when transmission is scheduled into packets of 4 slots using MCS4, and these 4 slot packets are transmitted...
I want to use a new source LF clock to raise the precision from +-250ppm to around +-20ppm. I already have an oscillator mounted in my PCB, so I want to use it for BLE. I...
Hi,
I would like to know if its possible to run Azure FOTA functionality w/o using Partition Manager (aka `SB_CONFIG_PARTITION_MANAGER=n`) ?
Trying to build this gets...
Can a BLE peripheral listen for scan requests or any commands from BLE central without making any advertisements? If this is possible, then it would save on the transmission...
Hi,
I was in a process of developing a central device with nrf51422 in PCA10028 board with NUS service client.I use SDK v12.2.0.We have an example code in the library which...
Hi:
I set up a peripheral on nrf52832 and add beacon_info data as Manufacturer specific information。The version of softdevice is s132.
memset(&scanrsp, 0, sizeof(scanrsp...
Hi,
My sensor uses SPI communication and need 32.768kHz external clock pin FCLK , I connect 32.768kHz clock to XL1 and XL2 but my problem is which pin can I use it for...
Hi All,
I've integrated the flash routines from this example:
github.com/.../nRF52-fds-example
into my project, and am having problems figuring out the architecture...
Hello,
I've done this with an Arduino and 1Sheeld Bluetooth LE shield, but want to try with the nRF52 dev kit. Just looking for any starter code/examples/tutorials to help...
I have a piconet of 4 devices, where 1 device is a master and 3 devices are slave.
Communication continuously occurs between master and the slaves.
But then the master...
After looking at Nordic's Bluetooth 5 implementation for nRF52840 and other chips -- it appears that Bluetooth BR classic is not available. All I see is BLE and BLE functions...
We are working on a project using nrf52832 module and GPRS device. Here we are facing a challenge in updating the firmware to BL652 over GPRS and server.
nrf52832 is connected...
Hello, a quick rundown on the problem here:
New versions of Softdevices S140 corrected an error and now correctly ignores writing to cccd descriptor using write instead...
I have 4 devices communicating in a Bluetooth piconet, where 1 device is the master device and 3 devices are slave devices.
I want to time synchronize the 4 devices to...
Hi,
I'm using the S132 v3 and wonder about the impact of DLE on scheduling.
In the chapter on Scheduling in the softdevive specification is writen that multiple peripherals...
I would like to setup the just released RasPI demo using the Nordic-Thingy52-Nodejs repo
I don't have a dongle, but 4 PDK 52840 boards and 2 Thingys.
Can I still use 1...
I found that blindly configuring all GPIO pins can stop the LFXO and RTC counter. I am reporting this as: something to be aware of, not obvious to everyone. Not a question...
