Hi,
I can't flash my PCA10040 dev board. I get this when I connect with J-Link Commander:
Connecting to target via SWD InitTarget() start CTRL-AP indicates that the...
In our product, we use Laird (Ezurio) BL653 BT module. In some countries such product requires SRRC certification. For SRRC certification we set BL653 to DTM mode with AT...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hello,
We are currently evaluating BLE Gateway (CIS, BIS) development using the nRF5340 Audio DK.
We would like to ask whether bidirectional CIS streaming is officially...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
I am using nrf51822 and softdevice 7.3. I am working on the github mesh example. I want to add uart service with mesh, so that I can communicate with that particular device...
Hello, this is what I can think of when porting a project, but before that, a little background about my project:
it uses BLE (duh)
it uses uart to print test output...
Hello,
i am using the nRF52 Development Board with SDK 11 and I have trubble with the UARTE Interface with DMA. Parallel I have running the ESB protocol.
I know the problems...
hello there i want to add battery service and thermometer service in advertisement packet. so i changed in uart project. but in advertisement project i can see battery service...
hi
I used the nrf51 dongle to receive advertisement packet from other nrf51 dongle. I used this formule, d = 10 ^ ((TxPower - RSSI) / 20) , given from this link forums...
Using Command Line Tools 9.0.0 attempting to push code.
ERROR: JLinkARM DLL reported an error. Try again. If error condition
ERROR: persists, run the same command again...
Hi All,
I am attempting to use 6 PWM channels with the app_pwm library on the nRF52 and am only able to successfully get 4 pwm outputs. Upon changing the 6th channel (PWM2...
I need 3 time aligned PWM channels (period of all three channels needs to start at the same time) at about 100 Hz with 16 bit resolution on the duty cycle. I also need to...
hello,
I used nrf52 and softdevice 2.0.1 and i have a big problem.
For some times the BT works perfectly but after i connect more then 4 devices for some reason
the...
Hi,
I need to check the emission of my custom nrf52832 board design and I need an spectrum analyzer... To see if my design would pass the regulations and tests.
I was...
Hi Nordic,
It's hard to find an example to talk about the event of advertising. I checked the advertising chart and know I will get the event BLE_GAP_EVT_TIMEOUT. Where can...
Hi,
I attended a training session run by the BT SIG last week and met a helpful Nordic chap who, when I mused about how I was using a programming board to run a sensor...
Hi i am having doubt in RTC configuration.I am using RTC1 and i want to produce ticks for every 1 minute.I have combined the UART and RTC example to get the RTC output in...
Hello
i am using the Nrf52 with pca 10036 board. i am working on fruitymesh to work on visualgdb.
i am getting problem here
"#pragma pack(push)
"#pragma pack(4)
...
Hello, i need to count 1 or 2 minutes. Someone can recommend me if to do that is easier to use app_timer or RTC?
Which is the value that i have to put in the prescaler...
