I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
currently, i am designing a wearable device using nrf52 as core soc. i just found that the nrf52 has two internal regulators, ldo and dcdc converter. in my case, the input...
I'm using a nRF51822 with 256KB flash and 16KB RAM, SoftDevice v5.2.1, uVision 4.71.2.0
I can compile and run the heart rate sensor, and it will become detected by mastercontrolpanel...
Hi,
I changed the chip from 16K RAM to 32K RAM. But seems the soft device report the below error when I use more then 16K address.
Error! Line: 0290, File: src\host_core...
Hello,
I'm interested to port a scatternet tree protocol but I'm not sure about that Gazell can support all.
My mandatory items are :
Each node can send or receive...
When trying to merge the Bootloader, Application, Softdevice 8.0 together I keep getting the error
"ERROR: The hex files cannot be merged since there are conflicts"
(happens...
I'm using keil nrf example ble_app_uart_s110_pca10028. I need to convert it for NRF51822_xaa.
I was able to create a new target and edit target settings for the NRF51822_xxaa...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
This post is not a question but a result of my analysis and so a answer to the above problem.
I tried both the Simple Uart Example from the Sdk 6.0.0 (Uart without interrupt...
Hello,
did someone made Altium footprint for J-Link Needle Adapter or managed to find it?
www.segger.com/.../J-Link_Needle_Adapter.pdf
I am planning to make PCB using...
Thanks to this post we can find USB port number of all segger devices connected.
But, as commented:
If I have both the dongle and the dev
kit (plugged to the PC...
Hi all
We use an external 32MHz crystal for the nRF51822 and set the register NRF_CLOCK->XTALFREQ to 0xFFFFFF00 according the reference manual V3.0, chapter 13.3. Afterwards...
I work solely under linux so need tool to generate init packet for DFU.
Is there existing tool/script for that under linux ?
(or plan for next sdk)
Thanks
Hello,
I want to send some data via the radio and then turn the radio to receive data. For the receiving, I need to setup a timeout. I would like to keep the timeout as small...
Hi, at the moment I'm learning about NFC and I don't know much about it. But I have question. Is it possible to use nrf52 NFC only for Bluetooth pairing purpose or can I use...
Hi,
I was trying to make nRF8001 peripheral device advertise the services and try to connect using an Android device that is having Nordic Master Control App.
I have...
