Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
I am running a standard schedule loop where I wake-up, service any scheduled tasks, then immediately go back to sleep. However, I am observing the following pattern:
...
Hi,
Everyone,
I have been working with Nordic NRF51422 with keil since laste 4 months.
Now I want to make Dev kit working on windows machine with eclipse GCC
Following...
Hi everyone,
When I run 4 instances (i.e., x2 PWM channels) of PWM with S210 (same example as the ant_background_scanning from SDK 10), after few seconds of constantly...
Hi, I am following the tutorial devzone.nordicsemi.com/.../ . to try to use eclipse to program and debug.
I have installed Eclipse on windows and I can compile without...
Timers are defined by a macro: APP_TIMER_DEF. This unfortunately expands to:
#define APP_TIMER_DEF(timer_id)
static app_timer_t timer_id##_data = { {0} };
static const...
Hi, we're working on a project that involves constant streaming of gyroscope and accelerometer data from an NRF51822 based module to a Linux machine.
What we've been working...
I am using the ble_uart_app on the dev kit with the nrf52. SDK version 11.0.0. How do I get the bsp_event_handler to get fired on a button release and button push event and...
Hi, I'm using stlink + openocd to flash and debug and it works fine.
But I want to measure the current consumption with nrf51822 debug interface off
Is there an equivalent...
I have a high-speed signal which I would like to sample with the nrf51's ADC. The signal is periodic (80kHz) and is from a low-impedance source (op amp buffer). I don't need...
I've been searched windows sample application for bluetooth.
I got android sample code but I need MFC sample code now.
If you have the sample code please let me know.
...
I've been playing around with the multi-central central/peripheral examples and I thought I would modify the peripheral to instead use a service I had written for another...
Hello,
If I supply 1.85V on the "External supply" pins, can i use all the modules of the board (nRF51DK)?
I need to have less than 2V on some of the pins as an output...
Our application is a smartband based on nRF 51822 with SDK 9.0 S130, and we found that the device will stop advertising unexpectedly (application is still alive). We have...
Looking at the radio section of the nrf52832 data sheet I see that in section 21.1.2 Packet configuration it is stated that
"For all modes that can be specified in the MODE...
