Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but I got to the part of the integrated DCDC converters and...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
I'm trying to study Message Sequence charts under the BLE GAP (Generic Access Profile) section of the s110 soft device.
However, I've noted that multiple links don't seem...
Hi
I'm studying at university and working on my thesis.
What I'm doing with a remote control and I want to measure the impedance of the antenna, because I want to be documented...
Using: nRF51822-BK-FW (v 1.0.1).
From within, there is the source files for ble_app_beacon_bcs that when compiled/loaded on the beacon hardware, causes the LED to blink...
Hi. I have been trying to follow nAN-29 to migrate from Keil to Eclipse without success. I was excited to find the blog, devzone.nordicsemi.com/.../ . The blog suggests that...
Hi all,
I just had some general questions regarding events and timers on the nRF51822. I'm coming from a Ti CC2540 8051 which used an OSAL system. This made it quite easy...
Hello,
While I was making SPIS part, I got several issues.
I am using STM32L151CB for SPI Master and nRF51822 for SPI Slave.
It seems many people had issues with SPIS...
I've made a modified version of the example DFU provided with SoftDevice v7.0.0-3 alpha that works in single bank mode instead of dual (because I need to bootload a huge app...
Hi all !
I have been working on an nRF51822 based board for a little while, the ten 1st prototypes worked well so we asked our factory to make 20 other with the same design...
Hi All,
Is the lite programmer which comes with the nRF51822 Development Kit sutable to program my code into nRF51822-Beacon?
If yes what cable would I need (supplier...
Hi,
I'd like to read PnP and the system ID from Device Information Service.
How can I initialize system and PnP ID? Are there any examples how to do this for nrf51822...
Hi,
I'm calling sd_ble_gatts_hvx and every once in a while I get an error code of 0x3401. I went through the SDK documentation but I could not find what that error code is...
Hi,
I have a peripheral device that needs to connect to both Android and iOS phones. Depending on which type of phone it connects to it is required to perform different tasks...
Hi
I tried SDK6.0.0 porject at below link.
C:\Keil\ARM\Device\Nordic\nrf51422\Board\nrf6310\s210\ant_bicycle_pwr
According to SDK documentation, we didn't need to modify...
Hello!
I need more battery life and higher resolution in my applications. That's why i need to level down the signal power, if it is possible. Thanks in advance.
