Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hello,
I am using nrf52840 DK, Segger Studio IDE, Win10.
My application is I want to transfer the image from iOS to the DK board.
I am aware of the Image Transfer...
I am working on a system with dual Bluetooth chips one acts as primary and the other as secondary.
I want these two communicate with a shared resource(Accelrometer)...
currently, i connected the nrf52(spi master) with ads1292 (spi slave) which is a ECG sensor. For the ads1292 chips, there is a output pin generating the signal called DRDY...
Hello evryone,
i cloned button example form github to sdk version 9.0.0 and i modified the neccesary changes between app.gpiote.c//nrf_drv_gpiote.c files and set the GPIOTE...
HI,ALL
there are two 'uart_event_handler' function in the project.
one in main, and the another in the app_uart_fifo.c
with the source code, i think when i input...
Hi everybody
I make an application which combine ANCS and NUS services on my device (nrf51 SDK 9.0.0,softdevice 8.0) This application works properly when I use IOS device...
Could you explain why 8 reload registers exists. Its use and use case. Since I believe we need to reload every register each time we have to reset counter.
I have a rare issue where my device won't advertising as it is waiting for a Pending Flash event to clear. However I want to add a supervisor time-out to this. It is safe...
Hi ,
I am getting error in pstorage_store function .
On further digging function
if ((!is_word_aligned(p_src))) is returning the error.
What does this function check...
I use nrf51822qfaa,s110 v8.00,keil MDK IDE. If the program is wrong,The chip will reset, I want to save some data to the FLASH area before the chip reset. What I need to do...
The example DFU project (dual_bank_ble_s110) for NRF51422 seems to work just fine on my custom board that has NRF51822. Is there a problem to use it like that if I set the...
Dear community,
I'd like to report a problem on the Direct Test Mode software provided in nrf51 SDK v6.1.0.
In this mode, 2-bytes commands are transmitted over the serial...
Whenever I try to run the following Convolution function for the 12th time in my code, the Processor is halted and I get the following Error on console:
Performing single...
According to this example, the device should be advertising RX and TX Characteristics. I also believe that when I connect to the UART app using my iphone, I should be able...
I have been successfully using my nRF52 Dev Kit (PCA10040) for the last few days. Today, when messing around with the UART drivers, I seem to have messed up the JLink-OB....
Hello,
I have an NRF51822 beacon board and two small 0.96" OLED displays (does not matter for me which one o use). One with GND, VDD, D0, D1, REST, D/C, CS and VCC pins...
