I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
In Bluetooth Spec (CoreV5.0, Vol6, Chepter6, Section1) it is mentioned that the random private address is generated periodically by a timer handler. I could not find any mention...
1.specification says that we should trigger EP0STATUS task to initiate the status stage for control transfer(read/write).
actually nrf52840 will auto ack the OUT TOKEN...
In Eddystone example in SDK 12.2.0, APP_MAX_ADV_SLOTS parameter is by default 5, but if I try to use less than 5, an error appears in es_flash.c because in the code, 5 slots...
hello there i want to scan particular device. so i am using whitelist. i change in hear_rate center code. but its not working. other unwanted devices are also scanned. i am...
Hi,
We are working with the nrf51822 on mBed platform
We have created the following profile under deviceinformationservices
in main.c
uint8_t DataCounter = 100;...
Hi there!
I found out that there is some problem in the example ble_app_hrs_rscs_relay in nRF5_SDK_11.0.0_89a8197. I want to restart advertising when adv timeout. I did as...
I'm trying to use app_timer_cnt_get() to implement an RTC Calendar system on a Gigawit module (nRF51822).
I have a test app_timer that has presacler=0 and period=3 seconds...
This is no a question, but i was not sure where to post it.
I was trying to use the nrfjprog command with the new version of SEGGER JLink, but the terminal output was ...
Hi! I'm trying to work with the beacon kit, but I have some confusion about which type of sdk I can use because with some example that I have found it doesn't work.
Besides...
When i use ble_app_hrs to connect with hrs demo(ble_app_hrs example), everything is ok.But when i connect to a heart rate monitor, it always disconnect.The print information...
I try to stop the advertising by using ble_advertising_start(BLE_ADV_MODE_IDLE) when the advertising is ongoing. It fails.
Please tell me how to stop advertising when the...
I have a problem where a central device (iPad) has to connect to a peripheral (running nrf51822, s110) as quickly as possible, receive data and disconnect again.
Right...
Hi
I would like to implement a radio peripheral in 2.402Ghz frequency which transmits some data, say of 31 bytes in radio which includes all header information abiding BLE...
I have a transmitter that sends 24 bytes of data every 10 ms. Whenever I run the receiver I only get new data once, then nothing. Here's my code
void mirf_config()
{...
