Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
My application need more than one of the host in the same area, we will set difference pipe of each host, we want to know the area already exist which of the pipe. Then we...
Is there a way to avoid fees, and still use BLE? Do I need to change UUIDs or leave them be?
If not can the nrf51822 be used to just use the pure 2.4 ghz protocol and DFU...
If a BLE device using nRF51822 has a freuqency drift around 80kHz (BLE limit is 50kHz). All other measurement item like ICFT can pass the BLE spec. Will the performance of...
Hi, this is my very first post to this forum.
I just received my nRF51 DK, so I installed a lot of stuff. The blinky example is running fine.
A question about nRFgo Studio...
hi, i am going to make a simple PWM with SDK 6.0.0, nrf51822 and softdevice.
first, i use ble_app_uart example as a base code, because i need to BLE communication with...
I have purchased a BLE module using nRF51822. I have used Agilent N4010A to test the RF characteristic of the module. For first log of the BLE moudle (300 pcs), all 300pcs...
Hello,
I want to serve webpage from nRF52DK via BLE.
In fact I got the kit specifically for this task.
I have installed GCC, Eclipse and SDK for IOT.
Thanks to the nice...
Hi
i have an application where 3 SPI devices are connected. Each of the devices have a different CPHA/CPOL configuration. This means that, in order to make this work properly...
I am changing my project from 6.x to 7.x, and I saw in the BLE Bootloader/DFU documentation that there is a point in the bootloader where it decides weather to use the init...
I am having power on lock up issues with my latest product design using nRF51422.
There is no external power monitoring ICs or reset ICs.
The system is relied on internal...
hello everyone ,
Well first I have to mention that I'm at a the very starting stages in using this great DK and I went throw some tutorials ...
Well , I have some questions...
Hi,
I'm trying to set up a link between one master and 10~ slave devices. All I need is a lowest latency and little data rate for short time.
And there is my question...
I'm using nrfgo to program nrf24LE1, and want to use commandline programming. I've tried to find an overview of the commands with no luck. Where can I find it? I've tried...
Hi all
The release notes of the S130 V2.0.0 states that an updated SoftDevice Specification can be found at the infocenter. But there is only the specification of S130...
