I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hello I am currently using the NRF52 DK2 PCA10040 with S132 soft device (nRF52 SDK v0.9.2) . I have setup my code to sample 4 analog pins periodically. I configured double...
Hi everyone,
Well, our device is based on NRF 51822 CFAC MCU. It’s an ibeacon based device which advertises and receives data frequently, and writes data into flash memory...
Hi,
I have a project that uses PStorage and the Nordic UART Service. PStorage is used to store a variable that is updated by the device, irrespective of the Bluetooth,...
Question:
From ble device I have to send some data or character to mobile in connected mode. After sending that data the device is not going to sleep mode while connected...
I'm trying to modify the beacon properties of the nrf Beacon in the nRF Beacon APP but it doesn't allow me to change those properties.
If I use the Beacon scanner the device...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi, I tried it from my Nexus 5, using the Android version of MCP. I can connect/unconnect, detect link loss, and (apparently) everything else, but only LED 1 seems to behave...
I want to connect one peripheral to a few central devices (lets say 3) but the central devices don't need to be connected to the peripheral at the same time. Should the PERIPHERAL_LINK_COUNT...
Thanks for the info already provided in devzone.nordicsemi.com/.../
I'm starting a new design with size (and volume) minimization a key requirement. Couple questions: ...
I am looking at the common nRF24L01+ module PCB with integrated antenna which is available at several suppliers. See picture below:
My question is - was this PCB design...
I'm using nrf51822, sd 10 and bootlader from sdk10. I can perform DFU to my application by loading the zip file with nRF master control.
Now I performed some customizations...
Hi
nRF51 dongle is no response from master emulation. I already did erased and flashed again few times but still not resolve.
I'm also restart my PC as well but the...
Dear nordic.
I am testing with nRF51822,
and have some question about hardware stability check.
Could I check below hardware stability, during or after system initialization...
i using a ble_app_hrs_freertos example, nrf52
I inserted a new custom task.
if(pdPASS != xTaskCreate(main_thread, "MAIN", 32, NULL , 1, &m_main_thread))
{
APP_ERROR_HANDLER...
I am attempting to make the change to peer_manager, fromd evice manager, and the in ble_advertising_start()
pstorage_access_status_get() call, I'm not sure what to change...
