Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
I'm develping my application with nrf52832 and nrf SDK v17.
I'm testing SPI interface so that I can use the external flash.
When I using SPI without BLE stack,the waveform...
hi support team,
if customer want to certificate device with 21540, which tool can customer use for dtm testing?
our tool can only set it to 8, can't be 10, as below:...
Hi,
Our products have been mass-produced and now need BQB certification, but the certification fails.
IC：nRF54L15 ncs2.9.1
base project: ncs_v2.9.1\v2.9.1\nrf\samples...
My product currently has DFU (Device Firmware Update) functionality enabled, but I want to allow firmware updates only after receiving a specific command via BLE. This is...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
so i was using the NRF51822-QFAC with an external balun and this antenna chip 2450AT43A100E .
now i want to move to the nRF52832 chip and from what i read is that...
Dear Experts,
I would like to better understand what exactly is accomplished by the mode-0 synchronization in Channel Sounding. My current understanding is that it seems...
The npm2100.overlay file generated by the nPM PowerUP app (v2.1.1) appears to have errors, and does not compile with the nRF Connect SDK Toolchain v3.0.0 in Visual Studio...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
I am trying to set up a w25q128 using SPI with a nrf5340 on a custom board and had a few questions. I have used DevAcademy as a reference as I do eventually want to set up...
Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
