Hi Nordic team,
I am using nRF54LM20DK with NCS v3.3.0 and trying to enable QSPI.
However, there is no &qspi or &qspi20 node in DTS, and adding it causes build errors...
Hello,
I attempted to rebuild the reference circuitry from the nPM2100, and I am measuring unusual power consumption using the PK2 outputting 1000mV.
Partially, I...
Hello,
I am currently working with nRF52832 and have been referencing the following sample code: nrf52-esb-ccm-example / ptx/main.c
I have successfully implemented AES...
Dear Everyone, We're using the PAN B611 evaluation board (ENW89861AXKF) which features a PAN B611-1C Bluetooth Low Energy (LE) module which is based on the Nordic Semiconductor...
Hi Nordic team,
We are designing a custom board using an nRF54L15 together with an nRF7002 WLCSP.
Our board has a single 3.3 V power rail. We would like to confirm the...
Hello,
We are currently performing power consumption measurements on the Nordic nRF9151 using the PPK2 in LTE-M with an Objenious SIM card.
During our tests, we observed...
Developing an implementation for UltraWideBandImpl for a different UWB hardware solution (not the provided qm35 implementation) and running into integration problems
The...
Hello. I'm using nRF52832, PCA10040, SDK13, S132 and "ble_app_uart" as reference.
When I connected board through by bluetooth, I couldn't see notification message which...
Hello,
According to the nRF Sniffer Guide 1.2, the sniffer is supported on a number of platforms (nRF51822/nRF51422 Evaluation Kits and others). All of them (as far as...
I am working on a project where my nrf51822 is on for long periods of time in lower power mode. Yesterday I made some updates to the code and the devices were working fine...
Hi Nordic team,
I print logs at each function in ble_bas.c. I used the App of nRF connect to test BAS. I can see on_connect, on_disconnect and on_write at enabling/disabling...
Hi,
The spec(nRF52832_PS_v1.3.pdf) said the peak current of TX/RX is 5.3/5.4 mA.
However, I use the PCA10040 board and the ble_app_template(SDK 12.2.0) sample code...
Hi,
I can see that Apple states that iPhone 7 supports LE Data Packet Length Extension forums.developer.apple.com/.../73168 . Anyone know if the packets per event and the...
Hi,
I have NRF51822 module with custom carrier board.
I trying the experimental ble app blinky (S130) with PCA10040 (master cenrtal board S132) works fine.
When trying...
Hello,
I test new SDK 13 and i have a problem. I don't success to debug bootloader. When i open .out file into debugger, sources are not complete (main is missing) so i...
Hello,
Is that possible to use a mbed application with SDK bootloader ? If yes, with signing too (if i sign application after generation) ?
How to set memory mapping...
I am trying to program an nRF52832 on an nRF52DK via the Debug in port (P18).
I am driving it with an STM32L073.
Should I put the nRF52832 into reset via the Debug in...
hai
in my application i am using nrf51822 . i have connected some sensors with the mcu. and i am collecting values from the sensors and this values are updated to the service...
In our code we use NV storage for system settings and calibration data.
I'm trying to understand when to open/close files and which structs to keep bwtween reads/writes...
Hello,
I'm using nrf51822/sd130/sdk12.1.0 and SOFTDEVICE_PRESENT defined.
But, I didn't enable softdevice.
I want to realize power save mode.
when I use __WFE...
hello there, i am using sdk11, i am using uart example. i am using nrf51 dk
SEGGER_RTT_WriteString is working. but
SEGGER_RTT_printf is not working. main.c
i have seen...
