Hi,
I have a couple of questions on migrating from Partition Manager to Devicetree since a particular example was not provided. Following the procedure in the SDK v3.3.0...
Greetings,
Although multi-NUS is not officially a sample in the nRF Connect SDK, it is closely related to nrf/samples/bluetooth/central_uart, and I thought it would be...
I have tried several code samples: nrf/samples/bluetooth/peripheral_uart and nrf/samples/openthread/cli. If I set hw-flow-control in zephyr/boards/nordic/nrf9160dk/nrf9160dk_nrf52840...
We recently encountered an issue with incompatible image partitions being pushed to in-field devices causing soft bricking. refer to this ticket for more information
Problem...
Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
I am upgrading from v12.0 to 12.2. I am using Linux, Eclipse, GNU ARM and Eclipse managed make.
I get compiler error ...nrfsdk12.2/components/drivers_nrf/hal/nrf_gpio.h...
Device: PTR5528
Board: custom.
I have just given coin battery directly to VDD. At P0.00, P0.02 i have two leds. On p0.03 and 05 i am having one interrupt and other is...
Hello everyone.
I am currently working on a device with some peripherals.
I have SPI slaves and other sensors that I am monitoring using GPIOTE driver.
I noticed a...
I am attempting to implement buttonless DFU with my application.
Using SDK v12.2.0 on a Rigado BMD-300 module (nRF52832)
Starting one step at a time, using nRFgo Studio...
I am running RTC in nrf51, after coming out of sleep mode RTC is getting reset.I want this RTC to keep running so that we can use it as wake up signal.
I am attempting to enable a second custom service with a vendor specific UUID with three characteristics (in addition to an existing custom service and the battery service...
Hello
I have created one custom profile using "ble_app_uart" project. Now I have an issue that I can't able to remove UART part of the code. If I remove the UART part of...
Dear Team,
when we compile in keil on one of the system we are getting hex file as 30 KB(Programme application which is correct one) & in another system we are getting...
There are three devices I am using (i)acts as Peripheral (ii)acts as Central and Peripheral and (iii) acts as central.
I connected device#1 to device#2, then device#2 to...
hi everyone!
I'm trying to use BDS with NRF52-DK with last SDK version.
I read manual here
to start develop my custom service in BDS.
i create my service and characteristics...
what do I need to change in the android studio settings to compile the nrftoolbox source for a Nexus 6 (api v23)? I get a bunch of compiler errors (Error:(25) No resource...
I’m using nRF8001-R2Q32-T in my design, RF Balun (part number: 2450BM14A0002T), and 2.4GHz Chip RF Antenna (part number 2450AT18A100E). My question do I still use any network...
Is it possible to program an NRF51 to wake-up from SYSTEM ON by either RTC or external interrupt?
I have some sensors programmed to wake-up by RTC but I would also like...
Hi
I'm using nRF5 SDK V12.0 and S132 on nRF52832, I add a peripheral service base on the ble_app_multilink_central example so that the phone can connect to the center....
