I want to achieve as close as possible to real-time tracking with the nRF9151. Because of the shared RF path this is somewhat tricky, LTE and GNSS can't run simultaneously...
Hi,
can anyone help me with this situations that i'm facing from a 1 month so i'm connecting esp32 controller to seengreat RS485 Dual CAN Bus moduler and the other hand...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Hello, We are building an application with NRF54 as the host MCU and NRF9151 as a serial modem. We are considering using a SoftSIM from Monogoto. Our main concern is how easy...
The last years I have developed a lot software (low level) for the nRF52840. I like this MCU very much, especially the SHORTS-Registers and EasyDMA are powerful for real short...
Hello everyone, I have a question regarding the LIS2MDL sensor. When I configure Register A, it correctly takes the value that I set. However, after the sensor initialization...
Hello,
I'm having trouble saving signing keys to the KMU on the nRF54LM20-DK.
I'm using the build for the nRF54LM20B, as recommended here, so the KMU should be used for...
I am new at this, I need to enable the OTA DFU mode on a nRF51822 QFAC chip on a pcb (the pcb has bluetooth).
how can I program it? what do I need to configure?
I am trying...
Hello,
I can't copy file from mail after updated nRF Toolbox to v4.0.4. (iPhone5s & iPhone 6Plus)
The app crashed when I select Copy to nRF Toolbox.
Any solutions?...
I found we have to build micro-ecc.lib on our own, so I follow the below link to start to build it:
Installing micro-ecc
Then, we meet the below to errors:
Makefile...
Im based in the example of SDK12.0 - MULTILINK_CENTRAL and i have to know the RRSI value in dbm if it is possible from the peripheral device that is connected to me but i...
nrf52 restart from main() after hit breakpoint and enter [Go] under IAR. It looks like there is some kind timer or watchdog to reset system etc... if stay in breakpoint (...
I have a PMIC in the device that I am building which will eventually take over from the battery. But I have to program the PMIC on startup, using the nRF52. I am trying to...
Hi,
It's the first time I'm developing a piece of code using Nordic SDK, so my question may be absolutely dumb!
We are working on a bl652 (with a nrf52 inside). I just...
I have an application that uses many TWI buses, on many pins of the nRF51. I handle this by initializing/uninitializing a single TWI bus for different transactions. I ran...
in S130 v2.0.0, what is address of central?
i'm using ble central tutorial successfully compiled.
in case of ble peripheral, i can set address whenever running.
so ble...
Dear Nordic Team,
Thanks for supporting.
How to add custom characteristics in standard service ?. I am using Health Thermometer service (HTS). I want to add two custom...
I mounted the chip onto my own PCB, I am not using a devkit, My board is "Wireless-Tag WT51822-S2", it is a module that uses nRF51822-QFAA as (SoC)
I am the ble_app_uart...
With the release of SDK 12.1 the Serialization of S130 is now deprecated.
Within SDK 12.0 the Serialization was supported NOT at all.
When this is true, I have to stay...
I'm trying to stream data in real time from 4 different sensor units to my computer. Each of these sensor units has an NRF52 module that sends data at 50 packets per second...
