I'm trying to add memfault to an existing project but I'm getting this error
I added this to my prj.conf
CONFIG_MEMFAULT = y
CONFIG_MEMFAULT_NCS_PROJECT_KEY = " 0EJm0WF0Ha0DUhnCOMjGOCYR7LIzzMOf...
I have a nRF54L15 firmware built on NCS v3.0.1, with image encryption enabled in mcuboot. Firmware needs to be updated to new version built on NCS 3.3.0.
In NCS 3.0.1, image...
Hi folks,
I am working on an nRF52840-based custom board using nRF Connect SDK v3.2.4 and have observed an issue related to runtime power management and PWM.
Environment...
Hi, is there a sample using nRF7002 on nRF54LM20B SQSPI (or could you share an appropriate devicetree)? I have been successful using the nRF54LM20 DK + nRF7002 EBII combination...
Hello.
I have nRF52840 USB Dongle connected to PC with nRFConect desktop application 4.0.4
I'm trying to connect to our custom BLE peripheral device, which advertises...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
As the datasheet showing
The GPIOTE input mode consumpt upto 22uA ,it is inconceivable.I want use NRF51822 to design a ultra low power consumption production ,and use...
HI:
I want to use nRF24L01+ as TX, and nRF51 Dongle as RX. And I try to use nRF51 Dongle to just listen for the RSSI of the NRF24L01+. Is there any example or reference...
Hi, I am new to nRF51DK. I am following this tutorial shown below:
developer.nordicsemi.com/.../a00066.html
After I flash my s130 softdevice, I follow the file directories...
Hello,
The intent of the implementation is to first connected to a central using fast advertisement and once they are connected the first time, if they disconnect, the...
Hi, i am going to tune my PCB meander antenna by soldering center conductor of semi-rigid coax cable directly on to the coplaner wave-guide trace and outer conductor on to...
Hi, i am designing a board using balun in it. Also, i am going to use meander antenna of nordic dongle(reference image is attached). As i can see, there is no RF coplaner...
Hello , I want know , if i used the Gazell Pairing Library (gzp) , it means that I can not use the ACK
Payload function ？if i can use the ack payload function place give...
Hi,
after reading the NFC with an smartphone the power consumption stays very high without doing anything else...
I don't know if this is related to this bug: "NFCT...
Hi,
I saw in the infocenter that the SAADC can measure the VDD directly. So in my case I want to check the voltage of a 3.3v coin cell regularly, I could do this without...
Hi Everyone,
The On Semi 7150SL reference design incorporates a dongle that can stream stereo music to two hearing aids which are equipped with the Ezairo 7150 module....
Dear sir,
Can we use NRF51822 OR NRF52832 as a slave device .As our controller is STM32F407ZET6 and we did not want to change any firmware from our previous version except...
I am using Keil to compile code and program into nRF51822 chip. SoftDevice s130 is used. There are various types of nRF51822 chips - nRF51822_xxAA, nRF51822_xxAB and nRF51822_xxAC...
Hi,
I need to measure the frequency of a PWM signal with 50% duty cycle through one of the GPIO pins. The frequency of input PWM signal ranges between 100Hz to 1000Hz....
