Hi,
As the subject says, I have an nRF54LM20A acting as a SPI slave. When I perform a call to spi_transceive_cb(), I don't have any data for TX (i.e. MISO). This runs until...
Hi Sirs
We are planning to use the nRF54LM20A/B together with the nRF21540 FEM in our design, and we have a few technical questions regarding TX power control and FEM...
Hi Nordic Support Team,
We are currently evaluating the nRF54L05 DFU single-slot sample in NCS v3.3.0.
Our question is: Is it technically possible to configure the single...
Hi,
I'm using the published nRF54L15 DK hardware files and noticed something that I don't understand.
On the nPM1300 section of the schematic and PCB:
Pin 20 ( VSYS...
we are developing solutions with PMIC type=PM1300, we eager to know the internal LDOs PSRR.
i have read 171 page of PM1300 datasheet, but cannot find PSRR data or the PSRR...
nRF54L15 PDM clock runs at ~1/32 of expected (PCLK1M instead of PCLK32M) on a custom board - works on DK
Summary
On a custom nRF54L15 board, the PDM peripheral clock ...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hello,
I need to get RSSI with the NRF51422 (pca10031, S110), but i don't want to connect with a central device (i.e. Smart Phone). The central device should scan for bluetooth...
We tried to pair with and connect to nRF51822 DK running HTM app with SONY VAIO fit15e NB and always fail as we did the following steps.
We also tried some devices like ASUS...
Hi,
I just replaced the BLE chip in my board from CC2540 to nRF51822. I simply want to know how to configure the interrupt on a pin as well as rising/falling edge interrupts...
What are the allowed channel numbers for gazell?
In the gazell user manual it states, a possible 80 channels.
While the nrf_gzll_set_channel_table () API reference says...
Hi,
Is it possible for me to completely copy the antenna design from PCA10028 unto my custom board? I don't need a very long range, but I need to make a design fairly quickly...
For PCA10001 have 16MHz crystal, and I use the NOP to test the cycle. And found the device work in 16MHz. How to set this board as 32MHz?
This is my current setting in...
We need to sample all 8 ADC channels for random 1ms pulses to record amplitude data from in real time. How much will that impact the bluetooth performance if it needs to freeze...
Dear community,
I would like to know how to send as much data as possilbe from a Nexus 4 to an NRF51822 based device. For that I think I need to send multiple packets per...
Based on the announcement for upcoming training ( www.nordicsemi.com/.../Bluetooth-Innovation-Trainings) it sounds like Nordic will support the Bluetooth SIG's Bluetooth Developer...
Hi, Is there a UART bootloader built in to the factory firmaware similar to others like NXP LPC series where a specific pin is held low at reset. If so what pins are used...
Hi, Nordic Engineers:
Pls give your hand, new question: Could i run two app on one mobile-phone that connceted with only one device? also, they can operate the device by...
Guys, I would like to put the internal uC in sleeping mode while nRF51822 is advertising and wakeup him, when I establish a connection.
I know that is possible, it must...
Alright, so I am having a lot of trouble generating a valid zip file to update with nRF Toolbox (android).
I used nRFgo Studio to flash dfu_test_app_hrm.hex and dfu_test_bootloader_b...
