Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
Hi i'm a newbie in nordic chip. Can someone please explain to me that how to enable and disable sleep in nrf51822 and what kind of setup need to be done?
Example in Arduino...
Hi all,
I'm currently working on adapting this example to fit my needs for testing a Bluetooth Mesh network.
I want to add the functionality for nodes to send to each...
Hi All.
I am aware that the USB nRF52840 Dongle does not support debugging but, can this device issue AT commands to a remote nRF52840 module in order to check the value...
Dear,
After adding the peer manager module of the SDK 15.2 and some other codes about configuring static passkey in the example "ble_app_uart" in ble_peripheral, I can successfully...
Hello,
I just install the nRF sniffer and have some trouble.
I use the following software version :
- Wireshark 2.6.4
- python 2.7
- pyserial-3.4-py2.py3-none...
Hello,
I am currently sampling SAADC every 1ms using PPI. Samples are collected in predefined buffer, and then send over BLE with ble_nus_data_send() function.
I would...
If I use sd_app_evt_wait() or nrf_pwr_mgmt_run, I lose TWI. In other words, in order to use TWI, I need re-initialize it. If I use:
__SEV(); __WFE(); __WFE(); It works but...
Hi,
The NRF52DK we use is interfaced to a capacitive touch keypad and an RGB LED. The board works fine when supplied by the USB but when we try supplying through the external...
I am trying to update the firmware via OTA , while uploading the firmware I am getting "upload failed" message on the nrf connect application.
I am using nrf51422 board...
We currently are investigating a move from nRF52832 to nRF52840. The reason for this is that we need a more powerfull radio - more range (even if that means lower throughput...
My environment: DK 10040, nRF52832, SD 6.1.1, SDK 15.2, SES 3.52
When does the SAADC use power? And when does it stop using power?
I searched the 52832 specification and...
I am trying to run the example from this page: www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit
I have PCA100040 somehow after running blinky and others...
I am trying to get a driver from a third party binary to work. Their library was compiled without using the HW FPU. I had to compile my code to use the softfp. I also added...
I posted on the Adafruit forum but there doesn't seem to be much support there. Since the module is based on nrF I'm hoping this community can help out.
For the most part...
