Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hello
I'm wondering if it is possible to upgrade over-the-air from SDK11 to SDK15.
I know already that using the example bootloader from SDK11 will not work because the...
Setup: nRF5_SDK_15.2.0_9412b96 / s132_nrf52_6.1.0_softdevice / nrf52832
I tried to make a multilink nus central (PCA10040) with 2 peripherals (PCA10028) connected to it...
Hi, I would like to send data from nRF52840 Dongle to Raspberry Pi 3 through USB-UART. I programmed the ble_app_uart_c example found in SDK 15.2 and I connected that to my...
NRF51822 RM 3.0 section 14.1 states each GPIO pin has DETECT, but where is the register to read per-pin detect? From the manual: "Each pin has a separate DETECT signal, and...
Hi,
Now, i want to use SAADC with softdevice of SDK15.0 to make a beacon program.
I migrate SAADC example in nRF5_SDK_15.0.0_a53641a\examples\peripheral to beacon with...
Hi,
I am using nrf_sniffer_2.0.0-beta-2_10Sep2018_3ef662e for capturing ble mesh packets but i am finding LE LL packets of my node with mesh beacons in my wireshark. Even...
Hello, I am new to nordic sdk and tools. I am planning to develop a nRF52840 DK based sensor device that reads I2C temperature sensor data ad broadcast it periodically. Also...
Hi,
I'm testing the BLE_UART example : <InstallFolder>\examples\peripheral\ble_app_uart . For this, I use the nRF52840 with SDK 15.2 and s140 softdevice.
I would like...
So I am using nrf52832 and making a whole new app in ios. My objective of the app is to get the sensor data (specially motion sensor data and accelerometer data) which is...
Hi,
I am trying to add app_uart into the heart rate sensor example. I called uart_config(); in the function function, but when I open the serial monitor, The errors shown...
Trying to build the unmodified light_switch_client_nrf52832_xxAA_s132_6_0_0.emProject from a fresh download of the Mesh SDK.
SDK_ROOT set & successfully tested as instructed...
Hi Team,
This is more like a generic question.
I have 100 beacons and I want to test them all simultaneously kind of a bulk testing.
What are the possible candidates...
Hello,
I would like to use the hardware crypto engine that is a part of nRF52832 chipset. I understand that the access to it is restricted as SoftDevice uses it. I wonder...
I am running into these 3 errors while compiling my program. I tried fixing sdk_config.h.
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol app_uart_init (referred...
EDIT: I have added the battery data in percentage to scan response manufacturer specific data. Is that the only possible way?
Hello,
I am working on a beacon application...
