Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hi,
Using the reference schematic No.4 given in the NRF52840 datasheet I made a design. I was able to test all the peripherals and range testing without any issues. But...
I am working on a custom I2C bootloader for nrf52832 using SDK 14.2.0. Currently, the bootloader can flash the application code very well. But I have no idea how to flash...
nrf_soc.h in these distributions reference symbols like SWI2_IRQn which aren't defined unless the build includes nrf51_to_nrf52.h, something I try to avoid when building for...
Hi, I'm working with nRF52832/nRF52840 and SDK 15 or 15.2 on Windows with Segger Embedded Studio.
Is it possible to use the device in low power mode, but keeping active...
My nRF52840 Dongle appears to have failed while its boot loader was being updated, the led does not flash red like it used to and only gives a short white flash on plugging...
Hi, everyone,
We are developing the BLE project on nRF52832 chip by using RTT / UART logging. Previously we monitored the project via UART communication port. But than we...
Dear Team,
Can you please review the attached schematic of NRF51822 used with matching Balun and chip antenna.
Balun: 2450BM14E0003T
Chip Antenna: 2450AT18A100E...
I have an application running on an nRF52 with the S332 softdevice which is a server which exposes a a few services each with a few characteristics. I am using the Nordic...
Can the nRF2460 be operated with TXLAT (0x52) set to a value lower than 4 ?
Can the nRF2460 have a lower latency than 20mS ?
The range requirements are very small (30...
Hi All,
I have created a custom board header file based off of the pca10040.h file. I have customised this to support 10 buttons and 2 leds. I have also extended the array...
Hi everyone ;)
I have a problem with timeslot ESB library with Bluetooth LE. In my application i need do somethingh like that:
Bluetooth and ESB PRX works excelent...
Hi, I am using the BLE mesh 2.2.0 with nRF5_SDK_15.0.0_a53641a. I am using Segger embedded studio as toolchain. I was able to compile and flash the default app code onto NRF52...
I am working on an application to connect approximately 500 devices in a single network... trying to check if Thread or Mesh is a better option... Please do suggest...
After searching around a little bit I found this post, but sadly an answer did never come up apparently. I'm using the nrf52 DK, using the 132 Softdevice.
I'm kind of at...
