Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
HCI for NRF52840
Hello
I m using a STM32 + NRF52840 and i have a mbed project in my STM32 and i want to use The NRF52840 only as a Bluetooth component, is there an example...
Hi guys,
I compiled the openbootloader example and when I try to run it on NRF52840, It gives segmentation fault:
(gdb) load nrf52840_xxaa_debug.hex Loading section .sec1...
Hi,
I'm having problem with the example code in the "Bluetooth low energy Services, a beginner's tutorial", the code was downloaded from github.
I'm using SES V3.5 for...
Hi,
We are currently develop our costum board with an nRF52840 SoC. Are the nRF52840 shipped with an initial bootloader to programm the device via USB? Because if possible...
Hello folks.
Easy question.
I want to add a .a static library to Segger Studio, but I don't know exactly where to add it. I know how to do in a Makefile with GCC, same...
I found the reference design files for nRF24LE1 from here ( https://www.nordicsemi.com/eng/nordic/download_resource/10898/2/41030525/1871 ), but I can't open them in EAGLE...
pca10059, replacing stock bootloader with Adafruit UF2, using USB dfu Hi. I currently don't have a J-Link at hand, so I tried to flash the UF2 bootloader using the stock DFU...
I want to keep both chip antenna and external antenna options on our board, what is best way to handle this for nRF24LE1 4×4mm QFN24 chip-set? Can I branch the Radio by having...
Hi,
I have a nRF52840 DK and a nRF52840 Dongle. I want to test to send binary data from one to each other using Bluetooth 5 or Nordic proprietary protocols. Are there...
Hi everyone, I am newcommer in here. I just buy one nRF52840 Dongle. I want to connect it with nRF52832 DK with ble_app_uart implemented; and open a COM port in MATLAB to...
Hi,
My application is based of ble_freertos_hrs example (SDK 14.2, nRF52832) and I need some variables to survive an assertion.
It appears that Keil has deprecated #pragma...
Hi Engineer： When I use nrf5_SDK_for_Mesh_v2.1 to debug the "light_switch" project, I always need to use a minimum of three boards (one as a provisioner, one as a client,...
I am using the nrf52832dk,i am working with the spi example for the sdk15,which pins are used for the spi protocol. I am enabling spim0.in sdk_config. h the pins number 3...
I am using NRF52832 as tags for asset tracking. I want to sense whether the asset is in movement or not as simple logical '0' or '1' response from sensor. Please suggest a...
I need sample code for the multiceiver mode. I want to send data from multiple NRF24LE1s as transmitter (to be exact 3 in number) to a single receiver. I read from the data...
