Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
I know that the SoftDevice has support for controlling a frontend with TX and RX signals.
However, our radio module uses a Skyworks SE2431L frontend with the control signals...
When using the script interactive_pyaci.py together with ipython and the serial example, I observe a strange formatting in the command window, because the "In [..]" is often...
SDK is nRF5_SDK_13.1.0_7ca7556.
Example is ble_ant_app_hrm.
Softdevice is S332.
The example can connect android but can not connect iphone.
Iphone 7 and ios is 10...
Disconnection of the peripheral is done without enabling another connection, the only way is to reset the module.
It happens sometimes after 5 min up to 1-2 hours.
If...
Hi all,
I'm working on an application that requires BLE. I've recently upgraded my project from sdk 14.0 to 15.2 in order to deal with some problems that I ran into with...
Hi,
I am trying to configure the nRF52810 clock setup to accept the LF CLK source from a pin on stm32l4xx on a custom board without much luck. My setup works correctly if...
Hello. I move ble_app_uart with a combination of nRF 52840-DK and SDK v 15.2.0. Using UART 0 or UARTE 0 confirms that it can communicate with nRF 52832 on the Central side...
Hi,
I am trying to understand the current consumption of a very simple BLE application running on the nRF52832 DK. For my final use case, I'd like to reduce the peak current...
Our project uses a Raspberry Pi compute module 3 connected via UART to 2 nRF51822. I'll go through what is working and than describe the issues I'm having
What's going...
Hi, I'm using ble_app_hrs_freertos from SDK 15.2 on PCA10056. I noticed that logs stop working (RTT) when I increase configTOTAL_HEAP_SIZE to 64k. I tried play with various...
I've got myself one an E73-2G4M04S1A board containing an nRF52810 chip for evaluation. I've setup an Raspberry Pi 1 rev2.0 with OpenOCD using this guide and wired it up according...
Hello,
i have bought 3 modules from Rigado (BMD-330-A-R) with a nRF52810 SoC, is it possible to flash it with an Raspberry Pi? I read that SWD is possible by its SPI-Interface...
We are in progrees of developing a wearable device using NRF52832 with BLE. The problem is, we have quite a few chips dead after several times of rewriting. The dead chips...
Hi,
I tried adding PWM for turning on/off the LED's on the DK for the Enocean switch example. It worked well.
I tried to perform dimming on the switch example by restricting...
