I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Hello,
Device: nrf52840DK
Software: nRFgoStudio (version 1.21.2.10)
Operating System: Windows 10 (updated)
I am not able to enable the reset pin. I am trying to...
Hello All,
I am trying to build the "bootloader_secure_serial" example from SDK 14.2.0 on IAR Embedded Workbench IDE ARM- 7.60.1 and I get this error: Error[Pg004]: macro...
Hi,
I'm trying to utilize PPI system to generate repetitive sequence of tasks (lets call them Task A, B, C, D, E, F) at 0,10,20,40,60,80 ms every second. i.e. I need to...
Hi,
I'm trying to test adding my own custom service, but have errors when I tried to add a 128bit UUID, the test code is simple, in the service_init() function, I just added...
I am using nrf52832 and sdk 14.2.0.The software I am using is keil 5.17.the error is as follows:.\_build\nrf52832_xxaa.axf: Error: L6915E: Library reports error: __use_no_semihosting...
Hi,
In nRF SDK15, Bluetooth peripheral examples for HID devices were limited to keyboard and mouse. By any means, can we configure Nordic device as a game controller?
Hello,
I am currently learning the PWM peripheral of the nRF52DK and am a total beginner in PWM.
I have tried running the attached program and this allows the LED0 to...
Hello,
I am working on a project which requires radio transmitter and receiver to work in sync with the SPI. So the setup is as follows the Transmitter transmits a signal...
Hi,
I am trying to write my own dfu updater for the NRF51 chip and I am stuck trying to make sense of the actual DFU sequence described here infocenter.nordicsemi.com/index...
I am trying to set up mqtt between 2 nrf52s and rpi3 with the examples of sdk 15.0.2. I am very new to nrf52, rpi3 and networking. I have read everything needed as much as...
Let's send a string over UART. RTS signal will go low (active). So far, so good.
The problem is that RTS remains active even after sending is done. And because it is still...
I have two boards. I ran the exact same commands on both boards. The commands flash the same bootloader+app+softdevice+app settings hex file. One board reboots into the application...
Hello,
Setup: Running Ubuntu 18.04 inside Windows Host (using VMWare).
Device: nrf52840DK
Operating System (used for development): RIOT
I would like to communicate...
Hi,
I am running IoT LWM2m example. Everything were going fine since yesterday. when I do hcitool lescan, i see following output:
hcitool lescan LE Scan ... 28:45:8B...
I am using the ble_blinky example (s132) and want to increase the number of characteristics. I get the error code 4. I think the storage capacity is not the reason why I can...
